Recent content by F350R

  1. F350R

    Intake modification Question

    Why buy a $35.00 block off plate when you can use a $0.50 freeze plug? Just wondering is all, my .50 plug is working great. I also removed the intake butterfly while I was at it.
  2. F350R

    19.5" Conversion - Who to use?

    I have some pictures at the house and a few on the camera that I don't have access to until probably later Friday evening. What ever you do don't put hard weights on these wheels or for what its worth never put them on your 16's again either Dyna Beads or Equal is the way to go. 4 Wheel Online...
  3. F350R

    19.5" Conversion - Who to use?

    I have a set of American Force rims with Hancook DH01 245x70Rx19.5 tires. I have roughly 7K on the tires I run 65Lb in the rear and 70 in the fronts. There is no chance that they will rub there is probably about two inches or more between them. They ride like a stock tire unless you feel that...
  4. F350R

    12V air compressors?????

    I have a Viair 550 compressor, with an old scuba tank mounted on the frame rail for colume. I have a regulator in the cab to fill the air bags as needed with a twin needle gauge to monitor tank pressure and air bag pressure mounted in a four aguge pillar pod. Don't forget to put a set of air...
  5. F350R

    New improved Turbo installed/ Pic's of old

    Thanks, $100 is better than not.
  6. F350R

    New improved Turbo installed/ Pic's of old

    Is the turbo covered under the 100K warranty or just the 36K warranty? My 04 sometimes sticks closed, rarely does it stick open above 28lbs. Maybe I should take it in if its covered by the 100k.
  7. F350R

    Oil Filters: Full flow and bypass

    I have a Frantz PT filter on my 04 F-350 it works great. I am in the process of putting a Frantz TP filter on my 02 Ketta TDI I haven't had time to build a bracket for it yet. Seems everytine I get a chance to work on it the wife is gone running the kids somewhere. The Frantz and Oil Guard...
  8. F350R

    is a wt. distributing hitch needed on f350?

    I am with architect I tend to load my trucks a little also The weight distributing hitch just makes it handle better and peice of mind that goes with it.
  9. F350R

    Alt on its way out

    Sounds like what happened to my 02 when the alt went out (burnt toast) it was extremely hot and smelled of burnt wiring. Glad it was under warreny at the time, the dealer had me wait while they changed it out. Bad part about waiting for it to be finished I drove home with my new alt incased in...
  10. F350R

    Bypass Oil Filters

    If your still looking for information on bypass filters here is a good site to visit with a ton of information about different lubes and filters. http://theoildrop.server101.com/cgi/ultimatebb.cgi
  11. F350R

    Reverse vehicle aid sensor

    I sure like mine I can back into the driveway up against the garage and know I have the truck off of the sidewalk. They are also nice when hooking up the trailer you can get right under the hitch on the first try almost everytime.
  12. F350R

    6.0 Gas Mileage

    I am getting the the same if not some what better mileage with my 04 6.0 dually (4.10 axle) than what I did with my 02 7.3 SRW. I deffinetly get better mileage with the 6.0 when its loaded and going up the mountains. When the tires wear out I will replace them with something slightly taller, I...
  13. F350R

    The official picture thread

    No we were up at Flat Tops above Glenwood springs, we went in from the East side which is a 30 mile trip up the forest service road. I need to get the rest of pictures posted from that trip. We hit the wild flowers in full bloom on that trip it something one would never forget. Here is a few...
  14. F350R

    ,03 F 250

    I sure hope you didn't scare him away with that list, I have about 1/4 of that stuff and that list was frightening to me. I am somewhat finished for a while the cheif finincial officer has confiscated my card, check book and threatened to chage the locks on the house.
  15. F350R

    Air tool?

    I have had a CP 3/8 drive for many years I got it when I was a wrench for a John Deere dealer. I used it more than my 1/2 drive as it is lighter and easier to use in many cases. Of course we had many uses for the 3/4 drive as well and a 3/4 drive 4Ft breaker bar that came in handy from time to...
See more

Members online

Total: 273 (members: 1, guests: 272)

Forum statistics

Threads
30,520
Messages
266,082
Members
14,629
Latest member
Colvinecoboost14

Latest posts

Top