Search results

  1. jeffnzoya

    Just shut down

    My brother has an 05 Excursion, 6.0 diesel. Yesterday we were on our way back home running on the interstate about 75mph on cruise. As he was comeing up on traffic he pressed the brake to release the cruise and the truck just shut down. We had it carried to the local Ford dealer and was...
  2. jeffnzoya

    Warning light

    Thank's for the info. I will pass it along. Jeff
  3. jeffnzoya

    Warning light

    My brother say's his 05 excursion has a light on in the dash that say's the door is adjar. Also, when he first get's in the truck the interior light stay's on for about 5 minutes. Has anyone had this problem? Thanks Jeff.
  4. jeffnzoya

    New wiring harness for 6.0

    we're gonna give it a try. I'll keep you posted.
  5. jeffnzoya

    New wiring harness for 6.0

    He did have the truck cold balance tested at Pro Diesel. The tech said it all checked out and their were no codes. How hard is this harness to put on. Is it a diy project. They are on ebay for $109.00 does that sound right. If so, I am going to recommend that he purchase one unless you...
  6. jeffnzoya

    New wiring harness for 6.0

    My brother's excursion has a miss at 1200 rpm and up. Has anyone ever replaced the harness on their truck and if so, for what reason and did it help. thanks Jeff.
  7. jeffnzoya

    Stock Excursion 1/4 mile times

    It was awful slow off the line but it felt like it was not pulling all the way through the gear's. It also has a bad miss. He can't be running on more than 7 cyl.
  8. jeffnzoya

    Stock Excursion 1/4 mile times

    I agree. I think the truck is bigtime slow. I would think in the 16's anyway.
  9. jeffnzoya

    Stock Excursion 1/4 mile times

    My brother took his 05 Excursion down the track the other day and it ran 19.3. I told him that seemed big time slow. What's the average time/mph for these trucks.
  10. jeffnzoya

    rough start and running

    Is this a DIY project? My brother has an 05 excursion and it is doing the same thing. He had a ford guy put it on the computer and was told to replace the #2 injector and the FICM, $1,200.00 later, no change it actually may run worse. Also you mentioned that if the HPOP is bad it will...
  11. jeffnzoya

    Bad Miss and power loss

    He went with NAPA fuel filter and he uses only ford motor oil.
  12. jeffnzoya

    Bad Miss and power loss

    My brother has an 05 Excursion with the 6.0 diesel and it had developed a very bad miss. After haveing a Ford tech put the truck on a computer he was told that the #2 injector was bad as well as the fuel injection module. A new module and injector, $950.00 later the truck still misses...
  13. jeffnzoya

    Edge programmer?

    Thank's guy's. I'll pass it on. By the way. Does $400.00 sound about right. Jeff
  14. jeffnzoya

    Edge programmer?

    Yes, he know's the orig. owner. He says it's a edge platnum and it is the top of the line in edge programmers. I also mentioned that he shold try it out prior to purchase. As far as EGT's, he would be ok without the pyro hooked up for a short while would he not. Thank's
  15. jeffnzoya

    Edge programmer?

    My brother has an 05 Excursion and has found a used edge with additude programmer. It's in a box and has several wires and cords that look like they plug into the factory wiring harness. It say's on the back of the little black box, "edge 10002 ver 5.3. The additude monitor is ver 1.29...
  16. jeffnzoya

    Fuel pressure 444E

    I have dial-up so it took a while for the pic's to download. In looking at the canester in the pic. it looks different from the one on my International. There was a twist off bowl to the back side of the canester and when I took it off, the screen was very dirty so I cleaned it with some carb...
  17. jeffnzoya

    Fuel pressure 444E

    A few months ago, I shimmed the fuel pump on my 00 7.3 increasing the fuel pressure to 70psi and have been happy with the results. I also own an 97 international with the 7.3 and hope someone will post instructions on how to do the same to it. The current pressure is pulsing between 38...
  18. jeffnzoya

    SCOTTY....I need more power!!!

    I am sure it is diy fixable, however I am running out of options. Jeff
  19. jeffnzoya

    SCOTTY....I need more power!!!

    OK, I am glad to get some feedback on this one. I am useing the word "blow off" because that is what is acts like to me. As long as I keep out of the throttle, and keep low boost, under 16lbs, it stay's on. However, when I get on the throttle hard and or let off hard it comes off. Also...
  20. jeffnzoya

    SCOTTY....I need more power!!!

    I replaced those gaskets a few weeks back. There was a bad leak and I just knew that would fix my problem. It brought me from 17 to 19, with the chip. Jeff.
  21. jeffnzoya

    SCOTTY....I need more power!!!

    Left out Sunday for Edisto Island, SC with our 29 Foot FWT IN TOW. As soon as I got started I noticed that the camper felt quite a bit heavier than I remembered it last. I was watching my boost guage and 19 psi for about a second was all I could get. I was expecting more with the heavy...
  22. jeffnzoya

    Checked out an edge with attitude today

    My cousin has an 08 super duty with 9k miles and while it is in the shop for the 6th time, (allready had the cab off twice), he was given an 07 250 to drive. It has an edge programer, looks like 4inch duel's and a BD intake. Since I am looking into upgrading to a shift on the fly...
  23. jeffnzoya

    EDGE products

    A friend has a 2001 Dodge 2500 5.9 24v and was given a Power Edge Comp Module. While reading the instructions, he saw that it looks like there are alot of items missing from the box. it looks like it was shipped in April of 02. Also, the instructions show alot of connections ie the...
  24. jeffnzoya

    Question HPX Mod

    Thankx for the tip dpantazis. I put my plugs in the barn with my factory airbox and AIH heater. Jeff
  25. jeffnzoya

    7.3 Engine ID question

    I think the shop that did my engine swap screwed me. I was suposed to get my old engine back complete, less the turbo and y pipe which they had to use on my engine, (the new engine came out of a 02 van with no intercooler). To make a long story short, all I got was 2 heads a HPOP, water pump...

Staff online

Members online

Total: 112 (members: 2, guests: 110)

Forum statistics

Threads
30,516
Messages
266,069
Members
14,627
Latest member
castellscl

Latest posts

Top