Recent content by FastColts

  1. FastColts

    Loose oil filter?

    Same experience with my first PSD years ago and assumed the vibration loosened the filter. Since then, and dozens of oil changes, I hand tighten and then put a little extra crank with the filter wrench... not too much to ruin the seal. No leaks since.
  2. FastColts

    hello

    Here's a link to an excellent "how to." Hope it helps.
  3. FastColts

    POWER STEERING / POWER BREAK LOSS help me

    I recall when the vacuum pump was going out on my '97 PSD that I had virtually no brakes at idle and had to rev the motor (6 speed) to get enough vacuum for the brakes to work. New vacuum pump solved the problem. I know it is a different setup from the later model vacuum pump but the same...
  4. FastColts

    Is AIC still available?

    I understand the apprehension about buying electronics, or anything else for that matter, from an unknown source but $500 is a bit much. I bought a new one complete from a guy on the "other" forum for $200 and have seen quite a few with PTO, bracket and harness for around that price. Either way...
  5. FastColts

    ???wicked wheel???

    Attached are three files with instructions posted by other members. Two are .pdf files with pics and one is text only. You will need Adobe Reader to view the .pdf files. Hope these help.
  6. FastColts

    Carpet

    I used to install automotive carpet and you will need to cut and sew to get roll goods to lay in there neatly. Pretty good job if it is something new to you; otherwise, I would order the molded carpet as suggested.
  7. FastColts

    where to get gauges

    I bought an ISSPRO, three-gauge pillar and a two-gauge overhead from dieselmanor.com and have been impressed with their customer service. Any questions or problems and you can get in touch with them quickly via email or telephone. Additionally, they have an after hours technical support line if...
  8. FastColts

    how to prep a gauge pod fpr paint?

    This is what dieselmanor recommends: . . . . . . . . . . . . . . . . . . . . . . . Gauge Mount Painting Tips 1) Prep the Gauge Mount. The first thing you need to do is remove any mold release that is left on the plastic gauge mount. This is best accomplished with an autobody wax and grease...
  9. FastColts

    no more mercon?

    Dennis, Excellent analysis and response. You make a lot of sense and I, for one, hope that you are correct. Good old capitalism and self interest are powerful forces driving our markets to provide what the consumer wants and is willing to pay for. Thanks!
  10. FastColts

    no more mercon?

    Any lawyers who think there may be some recourse and how to get it done? :dunno
  11. FastColts

    no more mercon?

    I just saw this and am a bit surprised to say the least. If this is accurate this will be a real problem for our transmissions which do not like mercon 5. Do I recall correctly that there is federal legislation requiring automakers to make replacement parts available for ten years after a...
  12. FastColts

    How much play in steering?

    You should have very little if any at all. What year is your truck and how many miles? You may be due for a replacement steering box. :(
  13. FastColts

    Truck won't start

    I have replaced many starters with the same symptoms on a variety of vehicles over the past 40 years. The internals can swell and bind when they get hot and won't turn until cool again. Hope it is as simple as that.
  14. FastColts

    4" Down Pipe HELP

    We installed an MBRP 4" stainless on my '02 and all fit fine. We did need to do a bit of twisting and adjusting the downpipe for clearance underneath. Get someone on the top to help while you are underneath. Leave the clamp loose enough to move the pipe and it should fit fine... assuming the...
  15. FastColts

    Steering box adjustment

    Just adjusted mine the same as on other trucks in the past... mark the edge of the screw with a piece of chalk and remember its position before you loosen the lock nut since the screw will rotate counter clockwise with the lock nut when you loosen it. Turn the adjustment screw 1/4 turn clockwise...
See more

Members online

No members online now.
Total: 218 (members: 0, guests: 218)

Forum statistics

Threads
30,512
Messages
266,061
Members
14,625
Latest member
woodrow58

Latest posts

Top