Ball joint replacement question

clintusaf · Apr 5, 2013

Okay. I'm getting my passenger side ball joint upper and lower replaced. I got a quote from the Ford dealer for 700 including parts. Should they be charging me for an extra hour of labor to replace the seals since they're already going to have everything apart?

DaveBen · Apr 5, 2013

That is the book time for changing seals. I guess it does not matter that they have the front end apart or not. All mechanics go by "Book Time".

Dave

xtrahappy · Apr 5, 2013

On the subject of ball joints. I have had more the one tell me it was cheaper to do both sides at same time instead of doing just one side. They said weak side put more pressure on good side, and most the time it was not all that long before the other side will need to be replaced. And if you did both sides at once you would have longer time between replacements.
What do yall think?

DaveBen · Apr 6, 2013

I have always replaced mine in pairs . While you are doing one side, it is not that much more work to do the other. Just takes twice as long.

Dave

BIG JOE · Apr 6, 2013

clintusaf said:
Okay. I'm getting my passenger side ball joint upper and lower replaced. I got a quote from the Ford dealer for 700 including parts. Should they be charging me for an extra hour of labor to replace the seals since they're already going to have everything apart?

Jus' my .03 Clint.. $700 is to much. I'd shop around a some ?

xtrahappy said:
On the subject of ball joints. I have had more the one tell me it was cheaper to do both sides at same time instead of doing just one side. They said weak side put more pressure on good side, and most the time it was not all that long before the other side will need to be replaced. And if you did both sides at once you would have longer time between replacements.
What do yall think?

Absolutly. Murphy's Law applies to doing ONE.. of Anything.. that has a.. Left & Right side.

DaveBen said:
I have always replaced mine in pairs . While you are doing one side, it is not that much more work to do the other. Just takes twice as long.

Dave

What Dave sez..

Joe

JimmyDee · Apr 6, 2013

I had mine done last summer for about $720 for both sides at a local front end shop. They used Moog parts. I did my own anti sway or roll bars for $140. About 45 min. Moogs as well.
Jim

Tail_Gunner · Apr 9, 2013

Back when I had to replace the ball joints on my 99, I too got estimates from local shops. The labor was in the low to mid hundreds of $$$$ range. Labor alone was more than parts.

After thinking about it, I said screw that and bought a simple 12 ton press from Harbor Freight and did the job my self using quality, greaseable ball joints. In spite of the cost of the hydraulic press, I still saved about $200 and I still have a hydraulic press to use when I need it.

DaveBen · Apr 9, 2013

That is what I did also. Got the ball joint job done and a press. How is it going for you TG??

Dave

JRJ04 · Apr 10, 2013

x2 on the price Clint. Just as a point of reference, I had my diesel mech quote me for it when i was thinking about doing it...It was going to be $1,000 for both sides...all in...parts, labor and alignment.

Keep shopping it!

Tail_Gunner · Apr 10, 2013

DaveBen said:
That is what I did also. Got the ball joint job done and a press. How is it going for you TG??

Dave

I'll start a TG update thread in the general stuff/lounge. Don't want to look like I'm hi-jacking the thread.

Ball joint replacement question

clintusaf

Clint

DaveBen

SDD Senior Member

xtrahappy

SDD Junior Member

DaveBen

SDD Senior Member

BIG JOE

Full Access Member

JimmyDee

God Bless America

Tail_Gunner

CRJ & ERJ A&P Mech.

DaveBen

SDD Senior Member

JRJ04

Senior Member

Tail_Gunner

CRJ & ERJ A&P Mech.

Members online

Forum statistics

Latest posts