Search results

  1. M

    What happened to everybody?

    I aggree, miss the site. I still frequent but dont always sign in. Has not been a lot happening on here. Maybe it will come back.
  2. M

    Question about early 99 Front unit bearing

    buy a later 99.5 to 02 front wheel bearing and replace the rotor to match. Its a lot cheaper then an early hub. later hub and rotor is cheaper then early hub alone. It will all bolt together
  3. M

    7.3 down

    its most likely the fuel heater shorting. Unplug it or it will take out another fuse. You dont need it. If you want one, they have better heater elements available.
  4. M

    Turbo o ring kit

    Replacement O-rings for Ford Diesel Engines has everything you need, bob(owner) is a good guy to deal with
  5. M

    Question Engine noise

    if your pcm is an xle4 from a 99 and you switch to a pmt 1 or pmt2 it will be quieter. My wifes 99 is a lot louder than my 01. I mean a lot louder. I love the diesel sound but mines nice.
  6. M

    using the snap on mt2500

    are you talking about the 2 black cartridges that go in from the front? mine says mt2500tsi on it then a date on the 2004 the other cartridge says mt2500vci also 2004 Am I looking at the right stuff?
  7. M

    using the snap on mt2500

    K2A is the key or just K2. I have one of these. It works good on the 7.3's. I have all the keys cartridges etc. I was thinking of selling mine but i need to get 400 shipped but its all there from what i can see. Case and all.
  8. M

    New engine oil change intervals?

    i think the 6.4 motors have a high pressure fuel pump and dont use oil pressure? common rail? I think
  9. M

    New engine oil change intervals?

    Correct on fuel dilution, The oils are much better now then they were. But if your injectors are leaking fuel in, which they do, or you have a dpf truck, then fuel in the oil is an issue. In a perfect scenario the oil is good for a lot longer, like 7500 or so.
  10. M

    Front end Clunk again!

    shock rubbers, ball joint looseness, or wheel bearing play. All will clunk like you are describing
  11. M

    6.oh no!

    keep in mind the factory used head bolts not studs. The factories metal was and is much weaker then the material arp uses in there studs. Not to mention a stud is much stronger then a bolt. Thats why race car use studs on everything.
  12. M

    Torque Converter Shudder?

    mine did the same, injectors were failing.(2 of them) have a cct test performed in the morning when the motor is cold. A week injector feels like a vibration at 35 mph. Thats approx when the tc locks up. When itslocked its direct drive. The vibrations are noticeable. Could be a converter or...
  13. M

    Hub needle bearing

    coarse thread was thru 2002, 03 up fine thread. Just would use different lug nuts. if it goes away with locked hubs, it very well may be the needle bearings ford part number c6tz3123a napa number b-2110 RockAuto Auto Parts has them cheap.
  14. M

    Question 4x4 Not working tried lots please help

    vacuume only operates the front hubs. It does not work the motor. Iff you have it in 2wd and hubs unlocked you should be able to reach under and spin the front driveshaft. If you flip the switch on the dash, even with vacuume issues, the front shaft should not spin anymore cause the transfercase...
  15. M

    Dot 3 brake fluid??

    advance auto's dot 3 is fine but dot4 is better.
  16. M

    Help Needed 99 SD 7.3 cold start problems

    advance auto part number for the relay is "gpr7" thats 17 dollars too. Its slightly different then the original with wire placemsnt but they fit. It bolts right in place. Its not that ord part number but the internals are the same. The correct part number one is 40 something but internally...
  17. M

    Question '08 F350 Front Brakes

    You can always grease the sliding pins. Use the correct brake grease.
  18. M

    4x4 dash light won't turn off!?!

    make sure the hubs are unlocked, grab the u joints on the front axles, see if you can spin them. If so hubs are unlocked. If one is locked get it free. ONce this is done spin the front driveshaft while the truck is in park. The shaft should also spin freely. If the transfer case is in 4wd it...
  19. M

    05-07 Grille upgrade on 99-03

    the 05 grill will fit by itself if you trim it. Just over 1/2 inch needs to be cut accross the bottom. Google it, there some good descriptions on how to.
  20. M

    Clunking noise

    i had a clunk when going into drive, then again, to reverse, ect. Was my transfer case.
  21. M

    7.3 light throttle = hesitation

    mnes doing it
  22. M

    driveshaft carrier bearing ?'s

    the pvc pipe will bang it right on. Just dont install backwards(not sure if it matters but theres a direction for the thing)
  23. M

    ball joint help please

    at least do both on the side you are taking apart. Dont just replace the lower and reuse the upper.
  24. M

    driveshaft carrier bearing ?'s

    i ripped the rubber off mine. I then cut thru the bearing top race with a cutting wheel. mI cut on both sides so it was 2 pieces. It came right off then the bearings fell out.The bottom race stayed on. I used my cutting wheel and caefuly cut thru it. One a cut was thru it it opened up enough to...
  25. M

    FYI early '99 front hub bearing

    all you need to do is buy the hubs and rotors for the same year. They are interchangeable. The hub and rotor must match. I have an early 99 with 01 rotors and hubs

Members online

Total: 83 (members: 1, guests: 82)

Forum statistics

Threads
30,537
Messages
266,113
Members
14,658
Latest member
NattyGlee22

Latest posts

Top