Search results

  1. bushpilot

    Question Oil change?

    what the heck is the "sample pump kit" ? and how hard can it be to fill a bottle after you open the fomoto oil valve...its not like you dont have to crawl under the truck to flip the drain valve open or pull a drain plug anyway...
  2. bushpilot

    Spray-on coating for aux tank?

    nice ! who makes that ? are you gravity feeding it ?
  3. bushpilot

    aux tank feed install how to?

    here ya go... http://www.rocketcityrockcrawlers.com/bigred/Aux-Fuel-Tank/Installing%20an%20Aux%20Fuel%20Tank%20paper%202007-06-18.pdf
  4. bushpilot

    aux tank feed install how to?

    if youre gonna do this do it right (the 1st time)...install and mount a fuel filter / water sep. between the in bed tank & the main (factory tank). Ill see if i can find the instructions that some one created (including all the fittings and parts needed) to do it right.
  5. bushpilot

    Hello

    welcome !
  6. bushpilot

    Question Keypad on door

    what year ?
  7. bushpilot

    I need some information.....

    Boat Maintenance Tips : Sea Ray Boats cleaning ink off vynil - Google Search id try armor-all or lexor leather/vinyl cleaner ?
  8. bushpilot

    Is Bigger Better?

    inmo the more data points you can monitor the better. I think if i were gonna add a 4th gauge it would be the HPOP...an important data point...and the only folks that make the hpop gauge are dipricol and its only available from itpdiesel theres lots of options for the 4th gauge, rear...
  9. bushpilot

    white crusty deposits

    it means your pushing coolant out the degas bottle. you could be over filling it... http://www.forddoctorsdts.com/articles/article-06-02.php
  10. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    youd be shocked at how little metal there is (beyond the skins) !
  11. bushpilot

    It finally happened to me

    what makes you think it was over boosting...i see 30psi all the time...peaks to 32psi are common. the clamps either worked themselves loose (combined w/ the oil mist) or were never adequately tightened, knowing the youve had turbine work done i suspect the clamps werent tight and the hose...
  12. bushpilot

    It finally happened to me

    you GOT to clean the mating surfaces of the hose & connection. i agree <there i said it> w/ f350drw1 use some form-a-gasket and tighten the clamps...LET IT Set up good before you drive it.
  13. bushpilot

    4x4 axle play

    your right dave... i should have said..."slid" in...as in LOOSE
  14. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    and that one doesnt even need any PARTS ! i could have used the rear bearing/tub :lmao someone should have told the poor bastard about the special button sequence that puts it into "self clean" mode !
  15. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    check this out...damm if i were closer.... Whirlpool Duet - Possible Parts - eBay (item 140235805137 end time May-29-08 20:36:02 PDT)
  16. bushpilot

    Question Oil change?

    so id say, test it...its cheaper than changing it and you MIGHT be ok to hold it beyond 6 months (if the truck is sitting a lot). for engines that dont get run alot, you might be better off using synthetic oils (since they wont break down as fast). engines that arent run enough to get...
  17. bushpilot

    4x4 axle play

    the front axles are pressed in...theyre on splined shafts, AT the inner & Outter axle ends... they have to travel "some" to compensate for angles and turning. the axles are held in by the steering knuckles (if i remember the proper assembly order)
  18. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    :lmao :clap: i always say anything worth doing is worth doing to EXCESS !
  19. bushpilot

    Question Oil change?

    which motorcraft...SYNTHETIC or CONVENTIONAL (dino) MOTORCRAFT® OILS AND LUBRICANTS fwiw - dino oil: Motor oil derived from traditional hydrocarbon/crude-oil sources (decomposed dinosaurs and plant matter). Also often referred to as "mineral" based oil. This in in contrast to the new...
  20. bushpilot

    Question Oil change?

    are you running synth. or dino ? when in doubt...sample it and get a report.
  21. bushpilot

    Question Oil change?

    i change mine every 5k...if i were wondering if i should change it sooner (due to lack of milage) id send samples off to blackstone-labs.com in my experiance (using rotella dino & sampling) 7000mi is pushing the oil... additives fall of after 7000 and the viscosity seems to drop pretty...
  22. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    Thanks ! The wife is happier TOO :sweet feels good to have saved the family money DIY ! its also supports "honey i REALLY need a numatic motorcycle service table" :sly
  23. bushpilot

    what to do???

    I'd go for it...but you should know the toughest boss youll ever work for is YOURSELF ! a good HONEST MECHANIC is hard to find...if youre one of those youll be able to PRINT money like its TP comin' off the roll ;) go into this EXPECTING to give your life to it for at least 5yrs...
  24. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    :lmao nice try but...i told the wife to run the hell outta the noisy bearing... run it til either it busts completely or until i get an afternoon to tear it apart !
  25. bushpilot

    photos REPAIRED: Whirlpool <DUET> !

    same one...just finally got 'round tu-it ! I went slow...i was told it "paid" 4hrs...and the professionals do it in 2-3hrs. it took me 5 w/ testing and lunch...id do it again in a heart beat...although i hope this bearing lasts longer than 3 yrs ! the whirlpool is EXACTLY the same...

Members online

Total: 124 (members: 3, guests: 121)

Forum statistics

Threads
30,565
Messages
266,218
Members
14,690
Latest member
Daddydirt79

Latest posts

Top