Search results

  1. ranaumo

    Vacuum control lines

    Well crap! My vacum control lines are starting to dry rot. Anyone know if I can order only the vacum line bundle, with the plugs on it - or if the dealer will only sell the wireing harness (since it is inside it - not an option). What I am referring to are the lines that the heater and A/C...
  2. ranaumo

    finaly killed the...............................

    Nothing wrong with Florida. It's a nice balmy 25 degrees outside right now. Come on down, bring your lawn chairs and have a party! :Budro Saw some fool out watering his lawn in this weather. If that sprinkler slows down long enough we might have an ice sculpture in our neighborhood...
  3. ranaumo

    Where to check next

    Howdy again.:) My problem is the truck is turning over real slow and not always wanting to start. Here is what I have checked/Done so far: Replaced both batteries with Optima blue Cleaned ground and engine contacts metered the batteries at idle - getting 14.5 volts Checked teh GP...
  4. ranaumo

    NEED HELP. TRUCK WON'T START. HAVE TO GO TO SCHOOL.

    GPR and or GP I agree with Bushpilot. When you turn on the ignition, does the battery gauge drop, then rise up after it runs a bit? If not, then it may be the Glow Plug Relay not fireing the Glow Plugs (easier to check and replace). Can also check with a meter across the terminals and...
  5. ranaumo

    ABS for Fronts

    Rabs Crap OK, I agree with the rabs unit being useless in an emergency stop (even on dry pavement it kicks in). Is there a way to disconnect it, or maybe put a reducer in line to the rear brakes to not affect the front braking when it kicks in? What options do we have? Also have not seen...
  6. ranaumo

    Fuel level float information

    Float Specs I seem to remember something being said about the float sensor having to work in a certain range to work in our trucks. Any ideas"? Ron
  7. ranaumo

    Front Rotors

    This will be the third set of lifetime swap front calipers on my truck. Does anyone know where I can find quality calipers where I do not have to worry the guy rebuilding them had a hangover that day? This is really frustrating having to go through this process yet again. The problem is...
  8. ranaumo

    Fuel level float information

    Well, after dropping the rear tank, cleaning it and putting it back in, I was thinking about how awfully small it is and such... I have a friend of mine who is willing to make me a tank out of 12ga steel (not shotshells :D ). I remember discussion a while back about only certain types of...
  9. ranaumo

    Addendum to Fuel Supply Modifications Wiki

    Peak Mt. Enta in Sicily. Was quite a climb going up the side the carrabaneri were not watching ;) Ron
  10. ranaumo

    Addendum to Fuel Supply Modifications Wiki

    Thought Hmmmm, since I have to do the side tank AND missed taking a pic of the pick-up assy for mine, I'll wait to send you the stuff and have both tanks done. Prob be in a couple of weeks as I have plans for a Vet get together this weekend:D Glad to help where I can. Ron
  11. ranaumo

    Addendum to Fuel Supply Modifications Wiki

    I was driving to work and my truck dies while showing 1/8 tank of fuel. I looked at the fuel regulator and it showed zero psi. It was the rear tank that was giving me grief. I went to the wiki and printed the paperwork to follow as a guide. Hutchinaugusta did a great job on the wiki. My...
  12. ranaumo

    Ball Joints

    Finished! Thanks y'all for the pointers and help. The Energy Suspension part for the twin I-beam bushings was 4.3121G (graphite - black). I did need to torch out the old ones. The sleeve I needed to reuse looked pressed in. I did not attempt to pull it out. While it was still warm, I...
  13. ranaumo

    Ball Joints

    Interesting, that's what I was told to do on my bronco, was to burn them. Just don't seem right, setting fire to the truck. Well I guess it's a good thing it's red (like a fire engine) :) I guess this will be a good use for that left over can of mapp gas, sitting on the shelf. Wonder if I...
  14. ranaumo

    Ball Joints

    OEM Well, I guess that means you're still running with OEM ball joints. That's good, so you didn't have to worry about excessive grease in the locker room...:roflmao :roflmao :roflmao Sorry, could'nt resist. Glad to hear from you. I do a fair bit of travelling through AL. It's usually...
  15. ranaumo

    Ball Joints

    Ball Joints Finished Well, job done and much thanks to y'all for the help.:burnit :burnit I went with the ones from Napa that have the lifetime warranty on them. Only problem was the funky blue polyurethane grease boots were somewhat squished when putting back the oem adjuster on the...
  16. ranaumo

    Ball Joints

    Ball Joint Work Thanks for the info. On JOATS page, he lists - F350 Upper Ball joint '94-'97...K80026...Moog/Fed Mog F350 Lower Ball joint '94-'97...K8607T...Moog/Fed Mog 3-StarJ.R. lists - F350 Upper Ball joint Moog K8432t F350 Lower Ball joint Moog K8433 Which one works best...
  17. ranaumo

    Ball Joints

    The movement was on the top and bottom direction, so I'm assuming it's the ball joints. My air compressor is lame and will not work for this. I am currently wireing my garage to upgrade the air compressor so I can do the work. Worse case, can I drive it with this movement so I can get the...
  18. ranaumo

    Ball Joints

    Ball Joinnts Yep, it's a 2wd. Bushings eh, Oh well. it's been a while since aligned. I'm getting almost 1/2" movement on the right and 1/4" on teh left wheels. Ron
  19. ranaumo

    Ball Joints

    Y'all, my truck now has over 150K and the front end has started to shake a lot. I recently packed the bearings and suspect it's the ball joints. How much work is involved with the ball joints, is it something the home guy can do? I do not have a press, or torch to heat the ends up. If...
  20. ranaumo

    CrankCase Modification

    Pace, right East of Pensacola. Ron
  21. ranaumo

    CrankCase Modification

    Hi All, I did my mod today and wanted to mention a point of difference. On the 95 PSD's the cast part has a reducer built in. Unless you have the updated air hoses, the 3" metal pipe will not work (that's the bad news). The good news is the fitting that bleeds into the cast part is held...

Members online

Total: 59 (members: 1, guests: 58)

Forum statistics

Threads
30,565
Messages
266,218
Members
14,690
Latest member
Daddydirt79

Latest posts

Top