Search results

  1. B

    Can't pull codes on 97 F350

    Three meters, from $50 to $250 can't pull a code from my truck even though the check engine light is on. I'm wondering if being a 97 it isn't fully OBDII compliant. One of the meters says there are 124 codes to pull but doesn't pull a single one. Does anyone else have a 97 that they can pull...
  2. B

    Pedal (Throttle) Position Sensor malfunctions

    My Pedal Position Sensor PPS, that is attached to the foot throttle assembly, works for 3-4 months then needs to be replaced. I have to replace it when the truck jerks alot, like it gives it fuel, then stops, then starts giving it fuel again. The fact that it wears a PPS out in 4 months makes me...
  3. B

    Starts very rough then smooths out nicely

    Hmmm. I run Rotella 15W40 (certainly thicker), and it is at 3500 miles. I change it every 5000. Since cold weather would make it thicker, I would think I would have this problem every time it gets cold, but I don't. I have thought like you did, that this problem sounds like the fuel or...
  4. B

    Starts very rough then smooths out nicely

    WHEN IT HAPPENS: sometimes in cold weather, but many times in cold weather it does not happen. It just seems to happen when it wants to, not because of any set of confitions. WHAT HAPPENS: The truck will start and run kind of rough, like it is missing 2 cylinders, or very rough, like it is...
  5. B

    Question Stealer want $$$ for ICP connector - where for less?

    Not sure if "Private" means "anyone" can't post here, but I'll give it a try. The dealer wants $73 for the 6" ICP wire connector (3 wires and the connector with clasp) that terminates at the ICP and I find it on line for $78! SUPER DUTY ICP CONNECTOR 97 03 7.3L DIESELand it says Huge...
  6. B

    Pedal Position Sensor wacked up

    I thunk of dielectric grease, but didn't put any in. There is no hole into the unit that is visible, but 100 PSI air does make it in. I'm sure better electrical contact would help, but grease that would collect dust might cause other problems. Life is one decision after another. I have...
  7. B

    Pedal Position Sensor wacked up

    Thanks for the input guys. The advice in this thread Oilburners.net says that this can also be caused by dirt or dust. I pulled the Pedal Position Sensor (PPS) off the truck and blew it out with an air hose. It worked like new, for a week, and is now beginning the same symptoms again...
  8. B

    Pedal Position Sensor wacked up

    Six months ago I was having to push my pedal down further than I had to prevoiusly to get the RPMs to increase. Then when I was pushing the pedal a little bit the engine would jump up and down in RPMs as if was quickly stomping on and letting of the pedal, but if I pressed it down more to...
  9. B

    HPOP oil separate from crankcase oil?

    The oil in the crankcase makes its way up to the HPOP reservoir and is used there to fire off the injectors. So when you change your oil you are refreshing that "Top End Oil" too. However, I have also heard that that is more theory than what actually happens. If the later is true, the "Top End...
  10. B

    Kevlar Busing or Needle Bearing Good or Bad??

    In the past 3 months I have put 2 complete clutch kits with the Kevlar pilot bushing and SM flywheels (replaced the original DM) from South Bend. The first job gave me huge vibrations, the second one leaves me with only bad vibrations mostly at 2400 - 2800 RPM. I just dropped my truck off at...
  11. B

    Question How to remove a read axelshaft

    Yes. I have removed the axle now. I was looking at the wrong manual. Thanks, BigRedWeather
  12. B

    Question Can't remove rear axelshaft

    Got my axel out, now I need to replace the seal... Thanks! My axle is out. Greatly appreciate your help. My son found that my manual does not match my truck. Little bit of a story behind that... No wonder my manual was missing steps! I can see the outer seal on the end of the axle...
  13. B

    Question How to remove a read axelshaft

    I am trying to remove the rear axelshaft so I can replace the oil seal on the driver's side. I am following the instructions from in my 97 - 2003 Haynes Ford Pickups and Expedition manual but my differential must be different because the instructions don't get me there. Here is what I...
  14. B

    Question Can't remove rear axelshaft

    I am trying to remove the rear axelshaft so I can replace the oil seal on the driver's side. I am following the instructions from in my 97 - 2003 Haynes Ford Pickups and Expedition manual but my differential must be different because the instructions don't get me there. Here is what I have...
  15. B

    Question Bad Pedal Position Sensor

    I pulled codes on my truck and got the following: -FAILED P0122 A circut low input -FAILED P0221 Pedal Position Sensor Performance Ford says I need a new Pedal Position Sensor - the thing you put your right foot on and the stuff that is connected to it - $441 - dealer only part! My...
  16. B

    Question Check Engine Light, Warm Engine, 1500 + RMP

    Today was the first time I saw the Check Engine light on. It only comes on after the truck is well warmed up and only stays on wnen it is running at 1500 or higher RPMs. I know the Check Engine light can mean about 1000 things, but I would like to start narrowing it down. Are there some...
  17. B

    Question U Joints going bad- what to do

    The mechanic that is doing an insurance replacement of a tie rod, says my driver side U-joint is bad and the passenger side is worse. I know you don't know what "bad" and "worse" mean, but I wonder what others' experiences have been. -Since only 1% of my miles are in 4X4 do I really need to...
  18. B

    Question Manual Transmission Filter

    Does a 97 F350 7.3L 4X4 manual 5 speed transmission have a filter? The filter the auto parts store sold me has a 12 X 16 inch gasket - no gasket that big on the transmission, Thanks, BigRedWeather
  19. B

    What is High Pressure Oil Pressure?

    Patrick and 95_Stroker, THANKS! Your posts were very helpful! Now I have an idea what I am dealing with. BigRedWeather
  20. B

    What is High Pressure Oil Pressure?

    Can someone explain what HPOP does for my truck? -Which aspects of performance does it effect? -What are signs that the pressure or volume are too high or too low? I have seen several posts about HPOP but can find none here, or on Google that explain it. Thanks, BigRedWeather
  21. B

    Where can I buy a scan tool?

    Is the ProScan OBD-II Scan Tool Good? Is this a good scan tool? At $149 it is fairly affordable. Does anyone have one they want to sell? Can someone point me to an article about how to use a scan tool, or an article on whether or not to buy one? Thanks, BigRedWeather
  22. B

    Where can I buy a scan tool?

    Where can I buy a scan tool? Anyone have a good recomendation? I have a laptop. Thanks, BigRedWeather
  23. B

    Rough start after new GPR and Oil Temp Sensor

    Location Richmond, KY 3 miles from Exit 97 off I-75.
  24. B

    Rough start after new GPR and Oil Temp Sensor

    IPC Yes, that helps (thanks alot)... but I still don't have it narrowed down. Do these test tell you anything? The engine was 35 degrees F for 8 hours. EBP disconnected, ICP connected Engine starts pretty easily 1 minute later EBP connected, ICP disconnected Engine starts less...
  25. B

    Rough start after new GPR and Oil Temp Sensor

    IPR Every picture I get on this is for a different model of truck and none of the electronic sensor look like mine, and they are in different locations (Significant parts were replaced and moved a year ago in this area on my truck). In the attached picture I disconnected A) and it started...

Members online

Total: 152 (members: 1, guests: 151)

Forum statistics

Threads
30,517
Messages
266,070
Members
14,629
Latest member
Colvinecoboost14

Latest posts

Top