Search results

  1. M

    need help deciding lift and tires

    My thought would be to plan exactly what you want, performance, look and wait until you have the funds to purchase you want. Plan ahead, spend less.
  2. M

    Help Needed Squeaking in front end...

    Yes, the stock type bushings which had been replaced 30K miles ago. Matt, are the axle mounted sway bar bushings the ones you put grease on? I assume you just lubed the original bushings or do you have aftermarket poly bushings? Thanks guys.
  3. M

    Help Needed Squeaking in front end...

    I used lube in my bushings but still have the noise.
  4. M

    Help Needed Squeaking in front end...

    i replaced my shocks and still have the same noises as you describe.
  5. M

    Rear end cover

    Does this newer rear pumpkin fit the 2000 F350 dually?
  6. M

    flush oil?

    I changed over to the Rotella synthetic 5w-40 from the Rotella dino oil. Truck does seem a bit quieter and smoother (engine wise) now. Start ups were starting to get just a little bit slower with temps in the 20's-low 30's. Will be interesting to see if the synthetic oil helps that at all?
  7. M

    flush oil?

    Maybe an old question, I decided to try synthestic (Rotella) oil. Do I need to flush/drain out my old oil in the system or can I just drain the old oil from the oil pan and fill with the new synthetic? Wondering whether any issue if there is some old dino oil getting mixed with the new...
  8. M

    Talk about the 7.3L CPS Here!

    I thought the gray one was the updated one and the blue one something "special"???
  9. M

    Talk about the 7.3L CPS Here!

    Is the blue one worth the price difference being sold on dfuser's website? Advantages? Improved Blue CPS for 7.3L Ford Powerstroke Diesel
  10. M

    Battery wraps

    It is getting colder and wondering if anybody had a good resource for battery insulation wraps?
  11. M

    smoky starting

    thanks!
  12. M

    smoky starting

    I too have experienced some rough idling during start up recently with a puff of white smoke from exhaust pipe. Where exactly is the relay located that you mention below? Official name? Thanks
  13. M

    fpr how to?

    My guage reads approximately 78-80 psi. Not sure if this is harmful or helpful?
  14. M

    rough start up

    It is a "romp". I installed the high pressore oil crossover about 5 weeks ago. Used the high pressure rubberized hose similar to the one from Diesel Innovations. Never had the "romp" before the installation. The "romp" only started within the last 2 weeks. Something else happening???
  15. M

    rough start up

    This has just begun happening when I start my truck. After my truck sits overnight, about every 5th time when I start the engine it idles rough. It sounds like there is a radical high lift cam in the engine, idles rough, then smooths out after about 10 seconds of this rough idle. Any ideas...
  16. M

    Oil in the CCV bypass tube???

    Where is best price for a CCV filtration system from Racor? Is there a real performance advantage by adding the CCV kit? When people speak about routing it to the exhaust, are you speaking about having it drip on the hot exhaust pipe to burn off OR drilling and tapping into the exhaust...
  17. M

    EGT sensor location

    sounds good...thanks
  18. M

    EGT sensor location

    75 degree's outside. Will see what they do when I pull my (light) trailer. Is the danger threshold somewhere around 1250 degree's for EGT's?
  19. M

    EGT sensor location

    Yep, drill and tap picture is where I stuck it. Thanks! My EGT's don't seem to get over 650 running down the road at 70 mph. No trailer. Walker muffler installed and Tymar intake.
  20. M

    EGT sensor location

    Am planning to install my EGT sensor in the exhaust but have read about several locations for mounting. Some off the top of the manifold, some off the lower exhaust flange under the truck...does either location really matter? The one picture I saw was under the truck at the bend...are they...
  21. M

    f250 subwoofer enclosure ??

    This is kind of neat idea for behind the seat...keeps jack in place...angled under seat edge. Not sure of price? http://www.mtx.com/caraudio/products/manualsQuickInstall/thunderforms/F250C00_specs.pdf
  22. M

    Transmission fluid flush pays

    For the transmission flush, are you saying to completely drain the transmission fluid by running the truck draining 6 quarts at a time, then drop pan, install new filter, clean magnet/pan - install pan, and then fill transmission with new fluid? I went to Wiki and the procedure does not come...
  23. M

    fpr how to?

    clearer...thanks!
  24. M

    fpr how to?

    When I click on the "How to shim the FPR" link, there are no pictures? I am intersted in doing this mod, but would like visual back up. Anybody know where pictures can be obtained? Thanks

Members online

No members online now.
Total: 103 (members: 1, guests: 102)

Forum statistics

Threads
30,516
Messages
266,069
Members
14,628
Latest member
Svttim

Latest posts

Top