Recent content by FordMastertech

  1. FordMastertech

    strange surprise under the hood

    That happens when you put the oil cap on top of the battery when it's off. The battery acid film on top of the battery will chew these oil caps pretty fast.:sorry FMT
  2. FordMastertech

    Spotted a sale on Ranchos

    I got that deal a couple of years ago when I got my RS9000X shocks from Sam's. They were great to deal with. FMT
  3. FordMastertech

    Leaking batteries?

    Make sure to check your charging system output voltage, it should be around 14 to 14.4 volts after the glow plugs shut off. FMT
  4. FordMastertech

    Cruise control dont work, air bag light on

    Needs a air bag clock spring FMT
  5. FordMastertech

    Check this out

    That thing will not help the issues with the 6.0s turbo. FMT
  6. FordMastertech

    Lights dim

    Belt slipping or a bad alternator. FMT
  7. FordMastertech

    Van Turbo Rehash

    I have a 2003 7.3 van turbo that is laying around and would like to install it on my Excursion. I know you need a adapter for the down pipe to make the conversion and eliminate the EBPV but the question is where to get it and what is the differences in the adapters if any and the cost. I mainly...
  8. FordMastertech

    Show off your Excursion/s here!

    FMTs X 1 FMTs X 2 :thumbs :burnit :sweet
  9. FordMastertech

    under dash data port

    You will also find the cigar lighter inop, check for a blown fuse. It should be fuse 12, 20 amp in the fuse box under the dash. FMT
  10. FordMastertech

    I have been busy lately

    Fit right in, some what but some trimming of the header panel is required. You have to cut all the old headlights mounting points off and open up the hole in the header panel for the 05/06 light buckets to fit in. The new lights have a bigger back side to them so this trimming is necessary. The...
  11. FordMastertech

    Excursion Tail Light Mod

    I have been looking at the Excursion tail lights and wonder why Ford never used the upper part of the light and installed a bulb there. I took the lights out and found no hole there so I drilled a 1 1/8 inch hole in the rear of the light after grinding the raised up nub off, 1 1/16 would be...
  12. FordMastertech

    I have been busy lately

    I never had a Hensley Arrow hitch and not many of them were around when I got the Pull Rite hitch for my 87 Ford van. The Pull rite hitch was taken off the Van when I bought the Excursion and I fabricated some brackets to get it to fit the 4X4 Excursion. I had Pull Rite send me some information...
  13. FordMastertech

    I have been busy lately

    The Excursion has got a make over and some new mods in the last year and it ain't done yet. :sweet :burnit :D It's now real tough to tell what year it is. :roflmao THE NEW LOOK
  14. FordMastertech

    Frozen front hubs after only 79k?

    You can put the hub in any old way so making alignment marks is not necessary. I know of no rebuild kits or serviceable parts except for the o ring that seals the locking hub to the wheel bearing hub. The only fix for them being frozen is to spray them with some penetrating oil and try to move...
  15. FordMastertech

    Pinion Seal

    The Excursion has a 10.5 Sterling axle in the rear. To replace the pinion seal you want to mark the pinion nut and end of the pinion shaft also count how many threads are hanging out of the nut. I use a prick punch to mark them and it helps in getting the torque and preload back in spec. When...
See more

Members online

No members online now.
Total: 112 (members: 0, guests: 112)

Forum statistics

Threads
30,516
Messages
266,069
Members
14,627
Latest member
castellscl

Latest posts

Top