Recent content by seawolf

  1. seawolf

    EBPV question

    I took the ebpv butterfly out, cut the shaft off to fit flush with the inside, put ridges on what was left of the shaft and pounded it back in at the open position. I also added a screw to make sure it stayed in place. I then reconnected the rod and unplugged the electrical connector.
  2. seawolf

    Instructions Replace Fan With Electric

    Is this what your looking far? This guy has several interesting mods. http://www.dzljim.com/Ford/fans.htm
  3. seawolf

    latest upgrades

    :watchout Paranoid I guess.
  4. seawolf

    getting ready for trip

    Oh yes, I'm an old ball bearing OR nurse and have scrubed many of those total hips. They are the best joint to have done. On the matter of 5th wheels, we started out with a 17' x 7' MeToo and a Datsun four banger. In the Good Sam mag, they just had a write up on Heartland's Sundance. It looks...
  5. seawolf

    latest upgrades

    Boy, you guys are keeping me busy and out of trouble except with my CFO!! Last weekend, I installed a 4" turbo back exhaust from Pinnacle. I left the 1st half of my Banks 3" and used their 3"-4" second half. To keep the Feds happy, I got a like new 4" Dodge cat real cheap:whah . Te He He. Need...
  6. seawolf

    getting ready for trip

    Are you hauling or towing? For the last decade or so, I have enjoyed the Oregon coast. Great storms now and the state campgrounds have winter discounts. A lot near towns with wonderful seafood etc. If your interested, I can fill you in on some of those from Newport South. Also, Silver Creek...
  7. seawolf

    Oregon version of cold air intake

    Grill mods I assume you noticed that I did enlarge the plastic grill openings laterally. Behind there, welllll it's functional but not so pretty. I removed the driver side solid radiator support and replaced it with upper and lower supports. I made these with angle steel and a piece of 3/4 x 1...
  8. seawolf

    Oregon version of cold air intake

    Tanks!! The upper 3" hose goes straight back and the lower one turns 90deg as shown in one of the photos. The "roof extension is held on with velcro. What doesn't show is another 3" hose from the finder well back to encourage hot air from the drivers side exhaust manifold to exit aft.
  9. seawolf

    Oregon version of cold air intake

    More info The one minor trial showed 20deg temp reduction inside vs outside the shield. Cheap gauges but??? Also, day before yesterday, I had to drive at highway speed in rain like a cow peeing on a flat rock and no water near the intakes.
  10. seawolf

    Oregon version of cold air intake

    After much reading on the forum, this is mod 2 and I think it will weather the rain. Any feedback? Next, THE CHIP!!! I'm looking for better MPG and pulling a 30 ft 5th wheel.
  11. seawolf

    Kitty Litter Cake ,you guys will like this

    NO ..............kidding
  12. seawolf

    Turbo Y to manifold intake hoses

    Local Ford monopoly
  13. seawolf

    hub covers

    I just got one. Identical except no logo. It has a much more secure galvanized retaining ring inside. :thumbs http://www.hubcaphaven.com/ HUBCAP HAVEN & WHEELS 103 6th St. NE, Bay #1 Buffalo, MN 55313 Item: Replilca Ford F250 , F350 Rear Center Cap Chrome Price: $40.00 Status: In...
  14. seawolf

    Turbo Y to manifold intake hoses

    I found it! F6TZ-6C640A @ $48.40 EA :eek:
  15. seawolf

    Turbo Y to manifold intake hoses

    What is the part number on those orange ___ hoses about 3" long from the turbo fresh air out y to the heads? How hard are they to replace? :hail
See more

Members online

No members online now.
Total: 83 (members: 0, guests: 83)

Forum statistics

Threads
30,568
Messages
266,223
Members
14,692
Latest member
dserge66

Latest posts

Top