Search results

  1. Strokin_Early_99

    Help Needed No start. Dead IPR maybe but I don't know...

    It was the IPR. The truck is running....... On 7 cylinders....................... Cylinder #1 is dead. It will not hold compression and there is enough crank case pressure to blow the filler cap out of my hand. DAMN!!!!!
  2. Strokin_Early_99

    Help Needed No start. Dead IPR maybe but I don't know...

    I have a no start situation. IRP at 65% and ICP at 150-160psi while cranking. I have pulled the injectors and replaced the O rings so they are good. I am thinking it is an IPR issue. I have pulled the stealth pumps and blocked off the front IPR so it will not have to be removed again to...
  3. Strokin_Early_99

    Front end bearings goin out???

    I swapped my truck over to late99-03 bearings and rotors. It saved me $200 a side by going this route in lieu of just replacing the early99 bearings. I have part numbers if you would like. Keep Strokin'
  4. Strokin_Early_99

    D66---IT'S HERE!!!!!!

    Modded flows 1250cfm. Cleans up the B codes real nice in all my tunes.
  5. Strokin_Early_99

    D66---IT'S HERE!!!!!!

    How are you going to marry up the intake Y to the 3" intakes?
  6. Strokin_Early_99

    D66---IT'S HERE!!!!!!

    My B codes were giving the D66 a run for it's money. I upgraded to a modded H2E.
  7. Strokin_Early_99

    D66---IT'S HERE!!!!!!

    How did the banks big head fit. I had to mill the rod down to fit and the hole was larger than the wastegate pin. But it worked just fine. I loved my D66.
  8. Strokin_Early_99

    Swapping PCM's into Early 99?

    I swapped my XLE4 PCM out with a PMT1 that Jody flashed with an enhanced stock tune for Big oil and single shot injectors. It made a tremendous difference in how the truck drives. It has more power and shifts better. I like the new trans tuning he has as well.
  9. Strokin_Early_99

    Up-pipe donut replacement Early 99??

    The donuts from CarQuest are the only ones I have found to crush right. The ones from Napa and Kragen are too darn hard to seal. If you do not have a car quest in your area, PM me and I can get some out to you. I just sent 4 to NY yesterday for a forum member. Keep Strokin'
  10. Strokin_Early_99

    Help

    Early 99 had a CAT, mine ran away from home years ago, I miss her!!LOL Check to see if your intercooler boots(blue boots) are tight and not torn. The big part of the K&N is it does not seal in the housing. Take a look at the seal and see if there are "seal marks" on all of the...
  11. Strokin_Early_99

    Super chip

    You can not stack a chip and a tuner on the PSD. The VIN lock will be gone of your buddy puts his truck back to stock. But when you program your truck, that will VIN lock it again up until you return your truck back to stock. Keep Strokin'
  12. Strokin_Early_99

    EGT acceptable range?

    I have watched my temps hold 1250 for the last 100K plus miles. I took my turbo off due to some very strange noises and found the exhaust veins melted down and chunks missing from heat. Be very careful at holding high temps for long extended periods of time. Dominator 66 turbo has been...
  13. Strokin_Early_99

    Boost?

    Wastegate will not stick open if you installed the wastegate correctly. Drop the rod over the pin and wind in 6 full turns. The blue boots are the place to check for leaks. I agree, you must have a leak to see that low of boost numbers. I would see 23-32psi of boost after install of...

Members online

Total: 57 (members: 2, guests: 55)

Forum statistics

Threads
30,565
Messages
266,218
Members
14,690
Latest member
Daddydirt79

Latest posts

Top