Search results

  1. snoman02

    Stealth HPOP

    Just a question for the community. We installed a stealth HPOP on a truck that we run daily. This truck pulls upwards of 20k all day, everyday. We started experiencing problems with this pump not producing adequate pressure. The pump was pulled and sent to stealth, under warranty, for repair...
  2. snoman02

    starving for fuel???

    I had this problem with my '02 F-450. it ended up being the screens in the fuel tank were plugged beyond belief. My mechanic couldn't believe the truck still ran. It would suddenly die, and started real hard. Might be worth looking into. Brent
  3. snoman02

    '02 7.3 A/C issue

    Preliminary testing has shown that the removal of the spacer behind the clutch has solved my problem. It's now officially an ice box.
  4. snoman02

    '02 7.3 A/C issue

    Ok Fellas, I'm having issues with my A/C. when first started, it blows ice cold, after 15-20 mins it goes warm and humid. a few mins later its back to ice cold. I have replaced the high pressure switch< and the wiring harness that controls the clutch also. what am i missing? Mid summer of last...
  5. snoman02

    Idle control module

    A couple questions for you guys. I'm looking for an Idle Control Module for my '02 F-250, if anybody wants to sell one let me know. The other question I have is, will one of these work on my manual trans F-450? I'd like to have it for snow removal in the event of having to jump another vehicle.
  6. snoman02

    Parking brake pedal issues

    I was really just wondering if anybody has ever done this? Can the assembly be replaced?
  7. snoman02

    Parking brake pedal issues

    My parking brake in my 450 no longer works. When depressed it does not stay latched to apply the brakes. With 259,000 on the clock and being used everyday for it's life to this point I think the mechanism is shot. Can I buy a replacement to bolt in my truck?
  8. snoman02

    Tony Wildman

    Guys just wondering if I missed something. I've been trying reach Tony by phone and email and I get no reponse. I'd like to get some programming from him but I have some questions.
  9. snoman02

    Turbo upgrades

    Ok fellas, I need some opinions/advice. My '02 F-450 is gonna be a work horse again for a while and I'm trying to get it ready. I'm gonna pulling a 53' wedge car hauler. I upgraded the clutch, intercooler boots, new up-pipes etc. I had to pull the turbo tonight because the waste gate stuck...
  10. snoman02

    Boost leaking

    While the truck was in the shop the up-pipes were replaced. The motor was out of the truck to replace the oil pan, so the charge tubes were off and inspected. I'm gonna try removing the red line to the actuator and unplugging my ebpv. Thanks again for the advice I'll keep everyone posted when I...
  11. snoman02

    Boost leaking

    Ok guys I eluded to this issue in a previous post, but I thought I had this problem fixed. On my '02 F-450 6spd I'm losing a terrible amount of boost. I just had the truck in the shop and had a laundry list of stuff done to it, including brand new dieselsite intercooler boots and valley boots. I...
  12. snoman02

    Traction bars

    Red Monkey, Thats kind of what I thought. I don't really want to lift my truck much cause I pull trailers alot. I just want to put heavier duty springs in the rear and then lift the front to match. We have a spring shop close to where I live I think I'm gonna get them to make me all new spring...
  13. snoman02

    Traction bars

    Ok fellas I have a few questions to ask. I am looking to do some small suspension mods on my '02 250. I want to beef up my rear springs and put a leveling kit on the front. My question is do 350's of the same year have more plies or just a taller block on the rear axle? Also I am looking at...
  14. snoman02

    Sensor locations for gauge install

    My boost gauge is in the line going to the MAP sensor, where the previous one was. And yes driving down the road I can barely get 10psi, I really have to beat the crap out of it to get 10.
  15. snoman02

    Sensor locations for gauge install

    Jordan, Ok I'll have to check the boots. I had an airaid full intake on it, so it should get all the fresh air it needs. Any recommendations on quality aftermarket boots?
  16. snoman02

    Sensor locations for gauge install

    Ok I got the gauges in and they all work. They look great too, but I'm a little worried that my truck only boosts about 5psi with a diablo 100hp tune in it! It's a 6spd man. Is my turbo just worn out? It does have 238,000 mi on it.
  17. snoman02

    Sensor locations for gauge install

    What size fitting did you use for the oil pressure on the top right? I'm having trouble finding something? My sensor is 1/8npt
  18. snoman02

    Sensor locations for gauge install

    Hey guys I'm putting new gauges in my snow plow unit and I need to know where to put my oil temp, oil press, and water temp sensors. I'd like to keep the factory ones if possible. If not it's no big deal. Pics would be great too. Thanks, Brent
  19. snoman02

    Help Needed Front Hub bolts

    I am having trouble with my front hub bearings. It sounds like my manual lockers are trying to engage partially. I replaced them with a new set of warns and that's not the issue. I read on here somewhere that someone had this problem with a customers truck and they had to replace the whole hub...
  20. snoman02

    clay bared

    I agree. I got the wild hair up my posterior one sat and decided to try this stuff. It worked great, my truck had some over spray on it and the clay bar took it all off. My paint is now as smooth as a baby's rear. I would recommend this to anyone. The only thing I would say would be to buy an...
  21. snoman02

    Pillar Gauge Pod

    Strokepower, I just put a set of Glow shift gauges in my buddies '96 250 and the pod that they sent with it was an overlay.Neither him nor I liked the way it installed but that's what we had. So I want to find one that replaces it for my truck. I like their gauges just not the pod.
  22. snoman02

    Pillar Gauge Pod

    Hey guys does anyone know where I can get a 3 gauge pillar pod for my '02? I would like one that replaces the factory pillar. I need one that will take 52mm gauges. Maybe that's a standard size, I don't know. I want to use glowshift gauges, but I don't like the pod they send with them that just...
  23. snoman02

    INSTALLING 08 MIRRORS

    I'm gonna ask a little more on this topic. I have 2 '02 superduty's that I want to put 03-07 mirrors on. Both of my trucks have the towing mirrors on them now. I want to upgrade to the newer ones with heat and signals in them. Could someone tell me exactly what I need to do the swap. Like which...
  24. snoman02

    '02 F-250 Tranny

    I hope, I was planning on buying a house before all this went down. OH well what are you going to do?
  25. snoman02

    '02 F-250 Tranny

    Well I ordered my new ATS Stage 1 trans today. So we'll see how it does.

Members online

Total: 193 (members: 2, guests: 191)

Forum statistics

Threads
30,517
Messages
266,070
Members
14,629
Latest member
Colvinecoboost14

Latest posts

Top