Search results

  1. C

    Show off your Excursion/s here!

    My 2K X 2K X
  2. C

    Need wiring diagram for GP controller on 2K X.

    Thanks Dave, I'm going to replace all GP's today and see what happens. Also going to replace the positive battery cable as the terminal on the drivers side had alot of corrosion on it. Bobby
  3. C

    Need wiring diagram for GP controller on 2K X.

    My X will not start when it's cold. Had batteries load tested, cleaned terminals, checked all fuses, only code was P0676 which was GP#6 ciruit fault. Did OHM test on all GP's and they ranged from 2-5 ohms, #6 was showing as an open. I want the diagram for the GP controller as it's a california...
  4. C

    Help fixing Excursion

    Thanks for the info guys. Would it be smarter just to buy a non EBVP pedestal or to try and plug up the existing one? I also have to remove the butterfly in the exhaust side of the turbo correct? What is the proper way to do that, and what about the impeller on the exhaust side? Is it toast...
  5. C

    Help fixing Excursion

    My 2000 PSD Excursion with 126k puked out all its oil from the turbo area. I removed the turbo and pedestal. O-rings will be replaced, but were not damaged in any way. It seems the oil was coming out from the pedestal where the EBPV rod comes out. Can oil get out from there? I added some pics...
  6. C

    Need exploded view of rear heater assembly

    Found it. The fuse from position #5 was missing. I have no idea why. When I was checking fuses I decided to see if there were possibly any that were missing, and that was the case. Thanks CHP for leading me in the right direction. Bobby
  7. C

    Need exploded view of rear heater assembly

    Checked out all fuses in dash panel and they were all ok. Bobby
  8. C

    Need exploded view of rear heater assembly

    Yes, I have done all those things and it is still blowing cold from the rear vents. I'll take a look at the fuses and see if any are toast. Is there fuses located anywhere else? Thanks Bobby
  9. C

    Need exploded view of rear heater assembly

    My rear heater is blowing cold air and will not change to hot with the temp control knob. Does anyone have an exploded view of the rear heating assembly and know how the temp is controlled? Is it vacuum assisted or electrically assisted? I would like to have an exploded view so I am not ripping...
  10. C

    Tranny not shifting correctly when warmed up

    I have a 2000 EX PSD with 120k miles. All stock except 1705 SCT. When it's first started it runs like a champ, perfect shifts and no problems. After it gets warm, when I take off from a stop and give it about half throttle it stays in first gear and RPMs go up to 3-4k. I have to let off and let...
  11. C

    Towing question

    I totally understand all your concerns, but I'm just helping the guy out. He is actually a friend of a friend. I also mentioned the fact that he is way overloaded. The 29k is just the tractor and the trailer, not the truck. He just asked me temp questions and that's why I asked. I know for a...
  12. C

    Towing question

    My friend has an 01 F250 PSD with 80k miles and will be towing a tractor and trailer totaling 29k pounds. He has all the necessary components taken care of to accomplish this; suspension,tranny,exhaust,guages,and he has added a superchips tuner. My question is what are the max EGT and tranny...
  13. C

    Need glowplug circuit wiring diagrams.

    Thanks scoutman, my email is [email protected] Bobby
  14. C

    Need glowplug circuit wiring diagrams.

    I have no idea, how can I tell? thanks
  15. C

    Need glowplug circuit wiring diagrams.

    I keep getting the P0676-Glow plug #6 circuit fault on my 2000 Ex. I replaced all the glowplugs along with new valve cover gaskets and injector harnesses. This fault keeps triggering my check engine light. I bought a Chiltons book, but it's worthless for diagrams. Does anyone have any that they...
  16. C

    Got codes, what should I do first?

    That's the harness thats integrated into the valve cover gasket right?
  17. C

    Got codes, what should I do first?

    I pulled these last night. Truck runs good until it gets up to operating temp then starts stumbling. P0470-Exhaust back pressure sensor circuit malfunction. P0478-Exhaust pressure control valve high input. P0603-PCM processor keep alive memory (KAM) error. P0676-Glow plug #6 circuit...
  18. C

    Newbie here, need opinions on my engine troubles

    Got codes, let's get this monster running again! Hey guys, I finally got my programmer and pulled the codes. Here they are, give me some direction on what to do first. Thanks, Bobby P1000- OBD II more driving needed. P0470-Exhaust back pressure sensor circuit malfunction...
  19. C

    Newbie here, need opinions on my engine troubles

    Yeah the funny thing though is that my Ex runs perfect up until it gets to operating temp. That's when it starts acting up. If a harness was unplugged it would act up from the get go. I'm still going to give those a look over though. Bobby
  20. C

    Newbie here, need opinions on my engine troubles

    Thanks for the welcome guys! I just bought an Edge Evolution programmer and I should have it tomorrow. I will pull codes and post them up so I con get a direction where to go next. What is this harness located in the valve cover? It's for the injectors? So then there is one on each side. Do they...
  21. C

    Newbie here, need opinions on my engine troubles

    Hey guys, I have a 2000EX PSD with 110k on it and I am the 3rd owner. It had the SCT 1700 installed on it. It recently started acting up on me. From a cold start it runs fine until it gets up to operating temp, then it starts bogging and chugging like a pig. It seems like it's only running...

Members online

Total: 90 (members: 2, guests: 88)

Forum statistics

Threads
30,565
Messages
266,218
Members
14,690
Latest member
Daddydirt79

Latest posts

Top