Recent content by BBT

  1. B

    Help Needed Wife moved truck for me, now stuck in driveway!

    Problem Solved! Thanks for all the suggestions. I tried moving the wheel as mentioned above, but couldn’t break it free. I even tried running a 3’ crowbar through the spokes for some extra leverage, but still no dice. What did work, me and another guy on each side of the wheel violently...
  2. B

    Help Needed Wife moved truck for me, now stuck in driveway!

    She moved truck to get her car out, then drove truck back to top of driveway. Auto trans. We have a very steep driveway. When I park I always apply parking brake first, then with truck in neutral and still running, let in roll back till it’s stopped and stable, then move selector to park and...
  3. B

    Need to replace wheel bearing

    Thanks to all. Got it done and it’s running quiet and smooth again. Went to NAPA to get the parts and ended up having to buy the hub nut socket, couldn’t find a rental anywhere. It was $52! Oh well, at least I have for the next time. BBT
  4. B

    Need to replace wheel bearing

    Noise, a rhythmic grind coming from the front left. Most noticeable when I let off the pedal and coast, can’t hear it too well when it’s rev’d up, though I can feel it through the bottoms of my feet. First noticed about 100-150 miles ago. I want to get it fixed tomorrow. D-60 with manual hubs...
  5. B

    Need to replace wheel bearing

    Can anyone point me to an article or wiki on replacing the front wheel bearings? Never done it before. Special tools needed? Other parts to check or replace while it’s open? Thanks BBT
  6. B

    Need a little help guys

    You might try pulling your glowplugs to make turning the motor by hand easier.
  7. B

    Question Replacing Serpentine

    Thanks! That got it done! BBT
  8. B

    Question Replacing Serpentine

    Hi all, Haven't posted in a while, but I do check in most every day. This weekend I need to replace the serpentine belt, and as I've never done this one before, I thought I'd check with you all for any tips and tricks to getting the old one off and the new one on. The tension and idler...
  9. B

    Getting P0237 code

    Thanks Rodney. I’ve printed the page for use this weekend. I don’t have a breakout box, so won’t be able to do the last two tests, but hopefully I’ll be able to get somewhere without it. Later, BBT
  10. B

    Getting P0237 code

    Hi all, Any hints on troubleshooting this? P0237-Low boost/MAP reading. What are some likely causes and fixes? Thanks BBT
  11. B

    94 chip install

    I've had mine out a few times and never pulled my tire or running board. There is a link somewhere for this, but couldn't find it now. Remove the fender liner fasteners in the approximately 11-12 o'clock to the 2-3 o'clock position(looking at the wheel well). Insert a prybar between the...
  12. B

    Whoooo Wheeeee !!!!!

    I bought a PCM from Jody T. last month with the same flash. I am very happy with the result! I had a Banks chip before and the difference with the DP PCM put on the big grin:D !! BBT
  13. B

    Yikes!! Can't get the hood up

    Thanks Rich, Was able to snake a 10mm socket through there and loosen the latch, found that missing screwdriver up there!:doh: We now return you to your regular programming. BBT
  14. B

    Yikes!! Can't get the hood up

    I tried to open my hood today but couldn't get it to budge. After releasing the latch you push down to fully let go, but it won't move down. Maybe I left something up there last time and it jammed, or perhaps my son sitting on it last night did it in, don't know. But I need to find a way to...
  15. B

    Need A Gauge Pod

    Here’s one from Banks.
See more

Members online

No members online now.
Total: 215 (members: 0, guests: 215)

Forum statistics

Threads
30,512
Messages
266,061
Members
14,625
Latest member
woodrow58

Latest posts

Top