Recent content by MrTailLight

  1. M

    Clutch Master Cylinder Bleeding Problem

    actually i did not do that. i know its creating more trouble for me now, but will i ever get all the air out...?
  2. M

    Clutch Master Cylinder Bleeding Problem

    well i had to change my clutch master cylinder, and i cant get this thing bled to save my life. we have gravity bled it, power blead it, and nothing! i have only 2-3 inchs of pedal and thats it. any ideas, lets hear em'!!
  3. M

    Question 94 F450 E Brake Pads Needed

    well it looks like i need to come off the cash and buy the unit. i hate to spend it but i need it. thanks for all your information, it was very helpful!
  4. M

    Question 94 F450 E Brake Pads Needed

    thanks for the heads up! i was about to order the pads and install them in the drum but Ford wanted $280 or so for them.....i think a bit high. Can they be rebuilt with minimal ease?
  5. M

    Question 94 F450 E Brake Pads Needed

    Hey all, i need some brake pads for my 1994 F450. this is in the unit that is on the back of the transmission. this truck has the 5 speed, 2WD. Where is the best place to buy them besides OEM.....i think that Ford is a bit proud of them with there price. thanks, Steve 419-210-0438
  6. M

    2000 Excursion Rear Brakes Sticking....?

    these were just dirty, cruded up. they are are clean and work like new.
  7. M

    2000 Excursion Rear Brakes Sticking....?

    well, we he dug into it and found that the calipers we sticking. the pins were free, but the calpiers were the problem. 2 pistons on the drivers side, and 1 piston on the passengers side.....took em off, cleaned them up, blew them out.....they work fine now. thanks guys!! Steve
  8. M

    2000 Excursion Rear Brakes Sticking....?

    hey all, my father in law has a 2000 3/4 ton excursion and the read breaks keep sticking and making the wheel assembly hot, by even just driving around the block. we have replaced the master cylinder already. we did take apart the rear lines and they did blow through....however, the rear...
  9. M

    Oil Temp Sending Unit.....

    where is this located so i can add this to my other gauge pod? i just need to know where to bolt the sensor into at??? i did get the other 3 gauges installed, all work fine and look way sweet! thanks for the help guys.
  10. M

    Need Help With Guage Install

    thanks guys! i got the EGT sensor done. boost will not be a problem. where is a good place to tap into for the oil pressure sending unit? heck, i might already have a similar one on it?? where would i find this beast??
  11. M

    Need Help With Guage Install

    ok all, i am finally putting in my guages.....boost, EGT, and oil pressure on the pillar post. where is agood spot to put in the sensor for the boost and the EGT?? i might have asked this a while back, but i am just now installing them. i hope tomorrow is the day! i already have the post...
  12. M

    94 Injector Needed Code AA

    well, i have a miss and need a good injector, new or rebuilt, either way. i need one at this time........where to go...........?
  13. M

    Need E-Brake Cable.....Where To Look??

    i just called ford and $28 gets the part, and it goes from the pedal to the trans brake. they said no cables to the rear wheels on this truck? dont know, never looked. and here i thought i would be having a $200 repair!
  14. M

    Need E-Brake Cable.....Where To Look??

    this one goes from the e-brake inside the cab and seems to be about 3-4 foot long and goes to a trans lookin brake behind the trans. maybe that same pedal does the rear drums and also the trans?? not sure, i did not look that far. ill check with ford and see what the damage is. i need my e-brake...
  15. M

    Need E-Brake Cable.....Where To Look??

    i need to replace my e-brake cable on my 94 F450, 5 speed. it is a short cable that goes to the trans. where can i find one??

Members online

Forum statistics

Threads
30,517
Messages
266,071
Members
14,629
Latest member
Colvinecoboost14
Top