Search results

  1. rgdillon

    My new 6.0 F250SD! Awesome!

    Well congratualtions on now owning a Ford . . . and a big welcome to the Diesel Family :thumbs I'm on my second diesel and can honestly say that I will never own anything but a diesel :D Congrats and good luck with her. Ron
  2. rgdillon

    Another New Member

    Hey Welcome :sweet Ron
  3. rgdillon

    '05 F-350 burned to the ground!!!

    Damn - first one that I have heard of. Had it happen to me once - my 77 GMC - but that was my fault. They do go real fast though - glad you were not hurt. Ron
  4. rgdillon

    03/04 Harness Recall -

    I had three recalls total. Recall 04B24 was for the tranny. 05S34 was for the wire harness along with the ICP connector. 05E15 was for the EP and connector with software update. These were for 03 and 04 6.0L motors. So you may have some of these. I'm sure Ford Doc there can give you a lot...
  5. rgdillon

    03/04 Harness Recall -

    Yep - before I'd post this over there I might as well run my head into a wall. That's why I posted it here, on OB and of course NOVAPS. To reduce my downtime - I was guilty of saving up all my recalls (3) and getting them all done at the same time. Worked out well - except for that stupid...
  6. rgdillon

    03/04 Harness Recall -

    If you have any surging, stalling, missing, seems low on power, etc etc – and you have not done the recall for the wiring harness . . . you need to get her in and have it done. I just finally got around to having mine done. I had the surging/missing deal and figured out that if I reached in...
  7. rgdillon

    rear sensors

    For anybody reading and curious - the dealer can reprogram the sensor so that the button acts as on/off button. Will reset to default on key off/on - or just hit the button to turn back on. This way you don't have to hit the stupid button everytime you go in reverse. Had this done on my...
  8. rgdillon

    Changing Injectors -

    Yeppers - I ordered the "install kit" which has all new caps - rubber lines and the spring clamps. Tried to talk him into installing a new pump also since it's the original - but not at this time. Anyway - suppose to all be here Thursday - I'm actually looking forward to this - my first...
  9. rgdillon

    Chip Position Recommendations

    I never could figure out what to do past three positions - tow mode - daily drive mode - and screw with the ricers mode. Ron
  10. rgdillon

    AutoEnginuity On the Way!

    I have it - coolest damn thing. It has already helped me when my EGR went out while driving. I just pulled over - hooked her up and told it to run the tests. No time flat I was back on the road. I also have an all Ford family - so I'm ready! Only thing I can mention for you to keep in...
  11. rgdillon

    Changing Injectors -

    Thanks for the info guys - looks like with all the suggestions here and from Agem - it should go pretty smooth. Thanks again, Ron
  12. rgdillon

    Changing Injectors -

    I need to change out the injectors on a 94 this friday - it's got 236K on it - original injectors. Have ordered all 8 with the install kit. Looking for any tips or info that I might need to know before I get started. Thanks, Ron
  13. rgdillon

    10K mod

    Anytime you add something that alters the way the motor works - you run a risk of the warranty being denied. So is it worth it - well since the thing only cost a buck or two - and it will add a smile to your face - yeah it's worth it. I ran it on my 7.3 before I got a chip - and then ran...
  14. rgdillon

    Door Seals, again...

    Thanks Joe - I might have enough foam laying around here - if not I'll be picking some up - this is moving to tops on my list of things to do! :thumbs Ron
  15. rgdillon

    Door Seals, again...

    Joe - Are you running this through the center hole of the existing weather stripping? Ron
  16. rgdillon

    What do you all think?

    I think that they look cool - long as it's someone else's truck :sweet I don't have a need for one - but if I did I wouldn't hesitate to get one. Looks good. Ron
  17. rgdillon

    Acetone revisited

    I must have visited several hundred web sites looking into this subject . . . and damn near every site points to the sites -PESWiki.com and/or lubedev.com - as the source for it's information. Apparently Louis LaPointe decided about 50 years ago to make it his crusade to promote acetone - it's...
  18. rgdillon

    egr valve is anybody having problems

    Just had my EGR and EBP replaced at about 24.5K Stock filters. Ron
  19. rgdillon

    I'm chained up now....

    Hmmm - buch of young'ens here - wife and I hit the 29 year mark last month . . . yep 29 years . . . twenty-nine years . . . two and a big ole niner . . . 29 times 365 days plus leap years. . . . that's umm . . . anyway - Congrats to the both of you :sweet Ron
  20. rgdillon

    Toro or Craftsman Lawn Mower

    Just to throw another mower into the mix for you - I bought a Troy-Bilt at Lowes three years ago - and love it. It has the tall rear wheels, self propelled - and although it's not electric start - it has a spring assist type starter on it. You only have to pull start it the first time you...
  21. rgdillon

    Need more info on the 450C VIAIR

    That's where I found the best price on the 450C - they are out of stock on the 550C (almost $100 more) - includes shipping. I already have an inverter installed - which pisses other contractors off when I just drop the tailgate and plug in :D - this should really send them over the edge...
  22. rgdillon

    Need more info on the 450C VIAIR

    I don't do Ebay - every since they cancelled my transactions (buying 7 cell phones) and turned me over to Wells Fargo for fraud investigation - the whole Ebay scene can go piss up a rope. Anyway - getting everything from two sources - the 450C, hook-up kit, tank, airdown kit, and a handful of...
  23. rgdillon

    Wicked Wheel

    Yep - what Bill said. Ron
  24. rgdillon

    Need more info on the 450C VIAIR

    Okay - I see this KIT And it looks like it has the gauge, pressure switch and stuff I need. So, that kit, the compressor, tank and then get my plumbing local should do it huh. Some of these people are nuts on the price of the 450C - Have found it for under $200 and one site for $379 :eek...
  25. rgdillon

    Need more info on the 450C VIAIR

    Okay - I want to add the 450C and a tank. Run the line up into the bed. Will run for tire inflation and a few air tools. Question is: what all do I need. Looking at the various sites I see pressure regs, switches, ports, etc etc. I have seen some say to mount the thing in a box? It's...

Members online

No members online now.
Total: 166 (members: 2, guests: 164)

Forum statistics

Threads
30,565
Messages
266,218
Members
14,690
Latest member
Daddydirt79

Latest posts

Top