Recent content by Dragon

  1. D

    1999 F-250 4X4 Rear Axle ID Help, PLEASE...

    Thanks guys!
  2. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    I agree Commander, I ended up replacing mine with the post 3/99 hubs and rotors, new pads, new seals, new o-rings, rebuilt the auto hubs, new Moog ball joints, new U-joints, new outer axle shaft and $1,200 BUX later! Now to tackle the rear end...
  3. D

    1999 F-250 4X4 Rear Axle ID Help, PLEASE...

    I am ready to replace the rear axle seals on my 1999 F-250 4X4. :coffee The Passenger side is wet and it's only a matter of time before the seals gives completely. I checked the air breather hose and it was clogged with dirt, so I am hoping that was the problem. If not, I plan to rebuild the...
  4. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    Attached is the Dana 50 (1998 1/2-1999 Pre March) Front Axle manual (F-250, F-350) which includes part numbers for those wanting this info. Also, I have included additional part numbers for this axle. The best deal on quality parts is from Bronco Graveyard. The Auto-Lock hub o-ring is a NAPA...
  5. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    OK... I pulled the passenger side hub. Looks good, no visible or mechanical wear or looseness. I plan on cleaning it up, packing the needle bearing and re-installing it. The rotor flange is indeed 13 MM on this side (passenger) also. The vacuum o-ring is there, but...the thrust washer was put in...
  6. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    JL, No problem man. I understand completely! TBar, thanks...I bought the truck new. I was never in an accident and I don't know for sure if the hub was ever replaced. I do know that I have had it to the dealer many times for the left front issues I have had. I am going to pull the right...
  7. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    No...I never pulled the hubs. I always had the dealer do it, and apparently they never actually serviced them even after all of my bitching & complaining about it. I have though serviced the auto-locking hubs at least yearly but never noticed a problem until recently. Why would the o-ring be...
  8. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    Well...I found the problem... :sweet NO O-RING WAS INSTALLED ON THE HUB AT THE FACTORY!!!! :clap: NO WONDER I HAD NOTHING BUT PROBLEMS WITH THIS LEFT FRONT HUB SINCE THE DAY I PURCHASED THIS TRUCK BRAND NEW! :eek: Also, the hub looks like it didn't seal properly around the knuckle...
  9. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    thanks Dpantazis
  10. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    bad Night, Yes, you have to change the rotors to the post 3/99 part. Well...bad news. I just fininshed taking my left wheel assembly apart. I am so lucky I didn't have a catastrophic failure! Not only is the hub shot, it destroyed the knuckle and the axle shaft. I have had trouble with this...
  11. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    Thanks Dave. I will check them out!
  12. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    thanks Dan! I am more concerned with the Part Numbers. I just saw those pages and made them into PDF files so I can go step by step. THANKS a million!
  13. D

    Question Pre March 99 vs Post March 99 Hubs - Interchangeability?

    Hi, GREAT FORUM! :clap: I have a Pre March 1999 F-250 SD, SRW, 4X4 and the left front bearing/hub is shot. I have searched the forums and could only find this thread and another one that wasn't very helpful. Question is...can I use the post March 1999 hubs on this axle. I realize I will have...
See more

Members online

No members online now.
Total: 49 (members: 5, guests: 44)

Forum statistics

Threads
30,565
Messages
266,218
Members
14,690
Latest member
Daddydirt79

Latest posts

Top