Search results

  1. M

    Clutch Master Cylinder Bleeding Problem

    well i had to change my clutch master cylinder, and i cant get this thing bled to save my life. we have gravity bled it, power blead it, and nothing! i have only 2-3 inchs of pedal and thats it. any ideas, lets hear em'!!
  2. M

    Question 94 F450 E Brake Pads Needed

    Hey all, i need some brake pads for my 1994 F450. this is in the unit that is on the back of the transmission. this truck has the 5 speed, 2WD. Where is the best place to buy them besides OEM.....i think that Ford is a bit proud of them with there price. thanks, Steve 419-210-0438
  3. M

    2000 Excursion Rear Brakes Sticking....?

    hey all, my father in law has a 2000 3/4 ton excursion and the read breaks keep sticking and making the wheel assembly hot, by even just driving around the block. we have replaced the master cylinder already. we did take apart the rear lines and they did blow through....however, the rear...
  4. M

    Oil Temp Sending Unit.....

    where is this located so i can add this to my other gauge pod? i just need to know where to bolt the sensor into at??? i did get the other 3 gauges installed, all work fine and look way sweet! thanks for the help guys.
  5. M

    Need Help With Guage Install

    ok all, i am finally putting in my guages.....boost, EGT, and oil pressure on the pillar post. where is agood spot to put in the sensor for the boost and the EGT?? i might have asked this a while back, but i am just now installing them. i hope tomorrow is the day! i already have the post...
  6. M

    94 Injector Needed Code AA

    well, i have a miss and need a good injector, new or rebuilt, either way. i need one at this time........where to go...........?
  7. M

    Need E-Brake Cable.....Where To Look??

    i need to replace my e-brake cable on my 94 F450, 5 speed. it is a short cable that goes to the trans. where can i find one??
  8. M

    No Turn Signals Or Brake Lights??

    Hey guys, question for ya..... on my super duty, i have no turn signals or break lights? i have replaced the turn signal switch in the column hoping this would take care of the problem, but it was a $140.00 part that did not fix my problem. yes the fuse checks good, and i replaced it with...
  9. M

    Starter Solenoid

    where is the started solenoid on this 94 PSD? i see a solenoid on the pass. side fender, but it does not apear to be for the starter, as the power cables are not big enough. i done a repo tonight, parked the truck at the shop, went and done another drive by for another repo, and i went back...
  10. M

    Installing Gauges Where To Put....

    Hey all, with my new goods soon to be here as far as gauges, i have a few Q's.... 1) i want to install my EGT after the turbo (like it is on my Suburban) is this the standard choice on this truck? if so, where exactly to mount the sensor? 2) where to install the Boost nipple for the line...
  11. M

    94 chip install

    i have a 94 and looking to install my power chip today, but all the info i can find show 95 & up. is the 94 the same as far as the location of the PCM?
  12. M

    Need A Gauge Pod

    I just bought a gauge pod for my pillar post, but i am looking to get a gauge pod that mounts on the dash for the 92-96 F-Series trucks. any info, input would be nice!
  13. M

    Is This A Good Chip?

    Hello, i will loking into getting a chip like this one. i wanted to get some input on it first: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=002&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=120045743099&rd=1,1
  14. M

    Just Bought A F450 Tow Truck

    Hello all, this is my first post on this site. looks like a nice place with some good info. i just bought a 1994 F450 with the PSD Turbo, have not gone through anything yet, just wondering what some good points of interest might be for checking out problems, or possible future problems. I...

Members online

No members online now.

Forum statistics

Threads
30,517
Messages
266,071
Members
14,629
Latest member
Colvinecoboost14
Top