Search results

  1. B

    Door Ajar Light???????

    Returned the Autozone part and bought the Ford part from the dealer for 3x as much. Whatever, I got gouged, but it works now!!!. My right rear door panel removal involved prying the red reflector off the bottom of the door and removing 7mm bolt, prying up the arm rest piece that has the...
  2. B

    Changing the oil in the rearend and front

    What is the correct capacity for the front and rear end? Don't want to buy too little and dont want a bunch left over
  3. B

    Door Ajar Light???????

    Is there a relay that could also need replacing??
  4. B

    Door Ajar Light???????

    I dont know, the part from autozone actually says Ford on the part. It has all the same markings and numbers as the OEM one I took out. I have un hooked the battery trying to create a new "zero point" with the door opened and closed and no change. The light is off when door opened, and on...
  5. B

    Door Ajar Light???????

    Took the old switch out. It was the problem. It had seperated into two pieces. Installed new switch and when I acuate it with my hand I get the dome light and door ajar light to go out. Now that I have reassembled the latch, when I CLOSE the door, the door ajar light comes back ON, and...
  6. B

    Door Ajar Light???????

    BTW, I did not actually laugh or cause any sort of a scene. It was a figure of speech. Had it not been for the knowledge I had gained here I probably would have let them fix it and take my money. So I have the door panel off, and the plastic sheeting pulled back. What is the best way to...
  7. B

    Door Ajar Light???????

    The part will be here by noon today, I should know if it fixed it by tonight.
  8. B

    Door Ajar Light???????

    Went to a Ford Dealership today when I got back in town. They scanned the GEM code and came up with a Right Rear door sensor. Quoted me $290 to R@R the door panel and install the sensor($62 parts, $230 Labor). I laughed and went to Autozone to order the Duralast version for $19.99. It cost...
  9. B

    Door Ajar Light???????

    No windshield replacement. Does Autozone have the proper scan tool to pull GEM codes. I'm out of town for 2 more days, which is why I ask, otherwise I would just drive over and find out.
  10. B

    Door Ajar Light???????

    Read Fact 4 of my first post. Opening any of the doors DOES NOT bring the dome lights back on. Witch is why I don't feel that it is a switch. What are the odds that All four switches failed at the same time. So where can I get scanned for free. Ford wants $99 to run a diagnostic.
  11. B

    Door Ajar Light???????

    Where do you get it scanned for free? A door switch would effect the doors not locking when it is shifted out of Park?
  12. B

    Door Ajar Light???????

    I do not think it is the sensor. As noted above. Once I drive and get the lights to go out. Opening any of the four doors does not cause the lights to come back on. Only turning the truck off will bring the lights back. Unless all four door switches failed at the exact same time??
  13. B

    Door Ajar Light???????

    Here are the Facts: 2003 F250 Crewcab 6.0 1.Door ajar light will not go out 2.Doors will not auto lock when shifted into drive. 3.Cab lights will not go out by turning the key to ON.(Yes I have checked the dimmer switch) 3. Cab lights will eventually go out once above ~10mph/1500rpm...
  14. B

    Spring bushings

    What is the correct bushing for a Fabtech spring?
  15. B

    Spring bushings

    I need to replace the bushings on my '03 6.0 as well. It has a 6" Fabtech on it. Will the energy bushings fit a Fabtech spring? Can the stock ones be removed with heat and an air chisel/hamer? Can they be removed with the springs still on the truck? If the springs are removed what...
  16. B

    carrier bearing holder

    Inland Empire Driveline Service, Inc. - Driveshafts, Pinion and Transmission Yokes, Center Support Bearings They have a poly-bushing support bearing, I think it was around $110, should last a while!
  17. B

    Upper Rear Shock mount/nut stripped

    I am trying to replace the shocks on my 03 f 250. I got all of them done except the right rear. If you look at the rear shock, the lower part of the shock has a bolt and nut that go through two tabs and the shock. The upper part of the shock mounts over a stud and is held in place with a nut...
  18. B

    Carrier Bearing and U joint Install Questions

    One last question: Any idea of a part number for the support bearing assembly and the three U joints? Thanks
  19. B

    Carrier Bearing and U joint Install Questions

    Perfect Dave, all of those PDF files are what I need. Thanks for your help
  20. B

    Carrier Bearing and U joint Install Questions

    Dave, Thanks for the PDF file, but thats not the part I am trying to fix. I am trying to replace the driveshaft carrier bearing, I guess it is also called the support bearing. It is about 2-3 feet behind the transfer case on the main drivline going into the rear diff.
  21. B

    Carrier Bearing and U joint Install Questions

    Axle is a C1
  22. B

    Carrier Bearing and U joint Install Questions

    Allright i fixed my PM's, it should be able to be sent now. I dont know if its a dana axle or a ford axle?
  23. B

    Carrier Bearing and U joint Install Questions

    I need to replace the carrier bearing on my rear driveshaft. While I had it apart I was also going to replace the U joints as well. I'm not worried about swaping the U joints, I've done the front axle U joints with out problems, I would imagine the rears would be the same. My concern is...
  24. B

    Edge Insight help...

    I have the same settup with the SCT and Edge Insight. What are good warning levels to set for the ECT, and Tranny Temp? I've set my EGT at 1100,1200, and 1300 as well. I think I have my Coolant Temp set to 215, 230, 245 Tranny at 195, 205,220. Do these seem close to a correct...
  25. B

    Questions about installing new hub?

    The truck is a 2003. What I did, and it seems to have worked, is pry the axle out of the axle housing a little. I guess the axle was too far into the housing. Once I pryed it out about a 1/4" farther, I was able to get all three washers on and the snap ring seated. Once this happend it...

Members online

No members online now.
Total: 20 (members: 0, guests: 20)

Forum statistics

Threads
30,517
Messages
266,071
Members
14,629
Latest member
Colvinecoboost14

Latest posts

Top