Recent content by NJKen

  1. N

    2010 flasher for LED lights

    Im curious if the flasher worked. If it did, Where did you get it and whats the part number? Ken
  2. N

    Injector Question

    The 6.0 injector is not like most other injectors. The can last 300k or 1k miles with no real reason. They are most sensitive to fuel and oil quality. I have always gone by the 50% rule with them. If there are 2 or more bad in one back, change four. If there are 4 or more bad on the truck...
  3. N

    Question 4WD HUB Noisy

    You need a special tool to install that seal on the axle and a special tool to seat the axle shaft with seal into the knuckle. Unfortunately the damage is most likely already done to the seal. Ken
  4. N

    Bent valve?

    You most likely have a bad injector. You should have someone do a cylinder contribution test on it to see what one is not pulling its weight. I had my local ford dealer do mine and check fuel pressure and fuel flow. I had 2 bad injectors on mine and you would have thought it needed an engine...
  5. N

    Alternator

    be careful with the higher than stock output alternators. Some of them dont really make any usable power untill higher RPMs. An example would be a stock alternator rated at 130a will make about 90a at idle and reach full output by 1300rpm. an aftermarket high output model will mag 50a at idle...
  6. N

    old problem new again

    It sounds like he is talking about the screen on the IPR. That could cause this. So could a leakdown in the high pressure oil rail. Ken
  7. N

    Help Needed Stipped out internal threads on hfcm drain plug

    Im not quite sure im following you but if you only need to remove the fuel lines there is a tool for that. The one I use is made by AST. They are not the only ones that make it so you may have luck at an auto parts store. Basically it is an aluminum tool that goes over the steel line and...
  8. N

    Help Needed 6.0 accel delay

    Changing 4 injectors got rid of the ridiculous lag on mine. After having Ford do a cylinder contribution test I realized I had 2 bad injectors not the one weak one I thought I had. Night and day difference in the truck after a 1,3,5,7 injector swap Ken
  9. N

    Motorcraft battery

    The higher the CCA the more plates. The more plates the thinner they are. The thinner they are the more fragile they are. Simple battery math! I have a set of the motorcraft 850's and can start my truck just fine on the coldest days here in NJ. Back in my younger days working at NAPA we had...
  10. N

    Power Steering Box

    Somebody has to get that lucky eventually! Usually the hose is gone when they start leaking. Ken
  11. N

    automatic 4wd hubs

    When you did the ball joints did you replace the big ugly seals with the propper installer? If not you will most likely find your problem there. Ken
  12. N

    7.3L Wont start in Park

    Yup. What he said:)^^ Ken
  13. N

    Help Needed ABS light reset

    ABS light will clear as soon as the problem is fixed. If its still on there is still a problem. Best thing you can do is get the codes. Ken
  14. N

    F350 - Loud banging from underneath

    If not that two other things to check are ball joints and wheel bearings. Had both those problems with my truck alreay and it makes some bad noises. Ken
  15. N

    Starting problem

    FWIW my truck has loped for a few seconds when really cold since day one. I bought it brand new. It has always started even down to -30 so I never paid it any attention. This truck has been really good to me. goin on 9 years of trouble free operation:) Ken
See more

Members online

Total: 197 (members: 1, guests: 196)

Forum statistics

Threads
30,512
Messages
266,061
Members
14,625
Latest member
woodrow58

Latest posts

Top