Search results

  1. R

    Wiper motor ?

    Well looks like my relay was fine so I am down to the switch and motor. When I turn the switch on ad pop the relay in and out it clicks. So there is power to the relay from the switch so I am guessing it is the motor.
  2. R

    Wiper motor ?

    This ia kinda embarasing I have had intermitant wiper motor issues. It started when I was fighiting an overcharging problem. the wipers would work on and off, ten when the overcharging was fixed I never saw any further problems out t it. Recently the issue is back. Initally if I left the...
  3. R

    Front axle hub bearing and seal HELP

    I found the same thing to be true. Have to pry stub axle out. If I rember correctly it is a PIA, pry out and push in with the clip. I usually only get it part way on then use a small hammer and punch to get it solid in the groove.
  4. R

    How to change the AC clutch

    I changed one on an explorer once but it was a real pain in the ass. Like to never got it off then had to warm the plate to be able to beat it back on with a rubber mallet. I was just hoping this was easier than that experience :)
  5. R

    How to change the AC clutch

    I need to replace my AC clutch on my 99 7.3. I cannot find any info on how to go about it. Looking at the new clutch it appears that all that is needed is a bolt to press the clutch disk off, replace components then draw it back on with the bolt that holds it in place am I over simplifying...
  6. R

    Checking the condition of the rear pinion bearing?

    Thanks for the replies. I looked the truck over today and cannot find an obvious issue. I am sending it in on Friday for a annual once over for my DOT inspection and will mention to him the concerns. We will see.
  7. R

    Checking the condition of the rear pinion bearing?

    Hello gentelmen. I have had a few pinion bearings go out in other vehicles and there was no doubt they were going out. Leaky pinion seal excessive heat after driving and vibration. This last 2 or so weeks on my 99 psd I have been noticing what i though may be a wheelbearing in the rear...
  8. R

    Question Brake spongey

    I had to order new calipers and bracket, both fronts are stuck to the outside so the inside pad is having to travel all the way out to contact the pad, or that is my best guess. I can feel the seperation of the pad and rotor. So monday the parts will be in and I will swap everything out for...
  9. R

    Question Brake spongey

    You talking about a loaded claiper? or is this something diffrent?
  10. R

    4 wd quit working for a short time.

    Hey Fellas this snow sux,,,, I used to love playing in it but I think I am over it. My side lot where I turn around and park my gooseneck is tight. When I turn around I have to jacknife the truck and trailer then pull out from under it. Not a big deal when dry but with a foot of snow on the...
  11. R

    Constant trailer wiring issues

    Luckily today wasn't bad, I had to repair one connection and reconnect a ground. Up and running in 15 min and 5 of that was looking for my wire strippers. Good thing too, roads were so bad a 2 hour haul turned into 4, and got the truck stuck in the drive..
  12. R

    Question Brake spongey

    Well I tried to get the pins today with no luck. I can't take it apart until I have the stuff to fix it. So I am going to hit the dealership tomorrow and try to have it in the shop tomorrow night.
  13. R

    Constant trailer wiring issues

    I was just wondering if everyone fights constantly to keep the lights working on their trailers? I bought a brand new trailer 3 years ago and it is pulled no less than 4 times a week. We went with DOT numbers recently and so i am a compulsive light checker (dont want a dumb ticket) it seems...
  14. R

    Question Brake spongey

    Yes dale I wuld be interested in that. It sounds like it could be several things but the most likely for my truck is the pins, I had 2 last brake change that had to be broken free, and I remember then thinking I needed to replace those before i had issues with them. I bet that is the...
  15. R

    Question Brake spongey

    I have a 99 F 250 Superduty, Recently the break peddel has to be depressed much farther than usual to get a response. I also notice that the bottom of the peddel is much spongier that I recall. Brake pads are in good shape and rotors are within spec. No obvious signs of leaks or loss of...
  16. R

    99 idle or wastegate ?

    I paid more attention to it tonight. When you first start it weather it is sounding like a jet or not, It will not rev up when you push down on the pedel. it is as if it gets enough fuel to Idle but not enough to pull. I just put the pedel about 1/4 down and the rpm's suddenly jumped up and when...
  17. R

    99 idle or wastegate ?

    YA it definately sounds like a jet, then back to sounding like a diesel, then jet,,, you get the picture. I am thinking it is normal. It could be the tranny fluid needing to heat up or maybee something is staying open,, as long as it won't leave me stranded or hurt the truck, I will just...
  18. R

    99 idle or wastegate ?

    When I start up my 99 and it is cold the rpm's run around 1200 and I can hear what sounds like the waste gate open and then 20 or so seconds later close. Sounds like it is trying to make music... Is that normal? This is the first winter I have owned this truck and my first powerstroke...
  19. R

    Oil Leak :(

    On my 99 f-250 I was changing the oil for the first time since it became mine and I noticed I seem to have an oil leak coming from up high on the block and appears to be in the area where the engine and bell housing meet. At first I thought rear main but then noticed drips on the starter mount...
  20. R

    New trailer

    Na fordtrucker I think I might rebuild it,,,,,,,,, Not really, I haul junk, and that one was absolutely junk. I got a baler hung up on it today,,, So the trailer is sitting in the middle of the field stuck until I can get back out with the highlift to extracate the baler.
  21. R

    New trailer

    14000lb 8 lug wheels. I love it. I am figuring out the quirks to making it work flawlessly. I love it... 3500.00 from http://www.appalachianmfg.com/
  22. R

    New trailer

    Well I finallly got tired of the multiple long trips I have been having to make hauling scrap, so I ponied up 3500 for this beauty. Added a winch and life is good.
  23. R

    Recomend a good Gooseneck hitch

    Bamma funny you should mention that cause I almost had a catastrophy today directly related to your statement. Criosing down a state road running you guessed it 58 mph (gotta eat up the economy when I can) I am topping some hills and notice a big black lincon type vehicle from the 70's about...
  24. R

    Recomend a good Gooseneck hitch

    Well if it dosen't work I cannot blame you guys. I just got mine installed and the only thing I do not like is it is welded in. It is a 5/8 plate with a screw in/out ball. Regardless it was installed well and bottom figure was 290.00 I will get to use it Saturday when i go get my new gooseneck.

Members online

No members online now.

Forum statistics

Threads
30,516
Messages
266,068
Members
14,627
Latest member
castellscl
Top