Search results

  1. Zero

    It just quit!!!

    I unlplugged the fuel heater on the side of the filter housing, replaced the fuse and fired it up. Thanks to all of you for your help. Now, what causes this to short out ? Do you guys just leave them unplugged or fix the problem.
  2. Zero

    It just quit!!!

    Blown fuse- What is it? I found a blown 30 amp fuse under the hood. I don't know what it is. It is located in the fuse box under the hood on the driver side fender area. The inside fuse in the middle row,(three rows of fuses and relays) it is the large fuse type, maybee 1 1/4". Anyone know...
  3. Zero

    It just quit!!!

    I have a superchips 1705 programmer, no chip
  4. Zero

    It just quit!!!

    I will go do it now. Where is the pcm /ecm? I still have my truck programmed, will unhooking the batteries cause any problems with that?
  5. Zero

    It just quit!!!

    All my indicator lights come on when I turn the key on. Operating normal in that respect. I just ment it did not give me a check engine light when it quit or after. The lights go out after a few seconds just like normal.
  6. Zero

    It just quit!!!

    Truck went down this morning. No warning, no symptoms, no warning lights. Driving 60mph and it just shut off. Not like running out of fuel, but just dead. Did this exact same thing 4-5 years ago and it was the cam sensor. Changed sensor on side of the road and did not fix problem - just cranks...
  7. Zero

    It just quit!!!

    No warning, no symptoms, no warning lights. Driving 60mph and it just shut off. Not like running out of fuel, but just dead. Did this exact same thing 4-5 years ago and it was the cam sensor. Changed sensor on side of the road and did not fix problem - just cranks. Plugged in my superchips...
  8. Zero

    pillar pods?

    Thanks for the info. Are all of the pods about the same quality and price? Any brands I should stay away from or look for?
  9. Zero

    pillar pods?

    Does anyone know where to get a triple pillar guage pod in grey for a 97 obs? All I have found are black. If not what kind of paint will work? (that won't peel off)
  10. Zero

    cps recall

    Tell me if I have this correct. If I have a black cps in my truck,(which I do) Ford will replace it with a grey one. If I have a reciept for the one in the truck,(which I do, from International) Ford will reimburse me for it. I did get a letter from Ford. Also, I have read something about a...
  11. Zero

    Two temp guages?

    Ok, Thanks
  12. Zero

    Two temp guages?

    I just picked up a sc 1705 cheap and am going to add guages. A pyrometer for sure, a boost guage-probably, a coolant temp-maybee. I have a 5-speed so I dont think I need a trans guage. Can a coolant temp guage be hooked up and the stock guage still work? I dont think I will like the factory...
  13. Zero

    Steering Column

    I had a mechanic tell me that's what it is but I don't know. As for the bearings falling out, they may already be gone. I've had the truck for three years and it has done it since I got it.
  14. Zero

    Steering Column

    I have a noise/rattle in my steering wheel. It makes noise at slow speeds when I hit a rock or bump. No sound when turning stop to stop. If I turn the wheel back and forth when the truck is off I hear the same noise. I think I have a bad bearing in the column, I was told there are two. How hard...
  15. Zero

    Fuel Regulator Screen Cleaning ** Updated **

    I partially tore my o-ring while cleaning the screen. Tried to get one from Ford but have to order kit for about $75. I found a phsysical match at my local parts store but it is an A/C o-ring. Both are green, I don't know how long it will last. Anyone know?
  16. Zero

    Front end Prob

    My parts store call them tie bolts. They come in different diameters and lengths. Good luck.
  17. Zero

    1997 downpipe help

    When you say up-pipe, do you mean the pipe that goes from the exaust manifold to the bottom of the turbo? If so, I have about .5 inch clearance there. That gap should not change as both pipes are mounted or clamped, unless I am missing something.
  18. Zero

    1997 downpipe help

    I got that sucker installed! Thanks for the info. I had to put it up on a lift to get the pry bar in from the underside. I am getting contact with something when I shut the truck off. I'll just have to find out on what then adjust the pipe. Seems to run much better and I don't have to keep my...
  19. Zero

    Loss of power

    What models have the dipstick that is two qts off? Is it low or high?
  20. Zero

    1997 downpipe help

    Ok, I was scared to let it down any. I already put the crossmember back on, but at least the nuts will come off easy this time! Zero
  21. Zero

    1997 downpipe help

    Thanks for the reply guy's. I had the tranny crossmember out but still had to cut the factory pipe at the top to get it out. How far can I let the tranny down with the crossmember out and not damage anything? When I had it out I kept a jack under the tranny for support. If I get this thing in...
  22. Zero

    1997 downpipe help

    Wow! What a ton of information can be found here, great site. I am having trouble getting my new 3" downpipe installed. I got the factory pipe out but I can't get the new one on. It is a two piece design and I can't get the the top piece to go down more than about half way. I bent the one...

Members online

No members online now.
Total: 223 (members: 0, guests: 223)

Forum statistics

Threads
30,512
Messages
266,061
Members
14,625
Latest member
woodrow58

Latest posts

Top